Handling Injection Molded Part Deformation: Pre-Mold Assessment and Post-Mold Improvement
Time:2026-11-17 08:21:19 / Popularity: / Source:
Target Audience: Structural Engineers, Mold Engineers, Injection Molding Engineers, NPI, SQE, Project Managers
Applicable Scenarios: Large-size PP/ABS/PC-ABS injection molded shells, bases, brackets, smart pet hardware, home appliances, robot structural components.
Core Concept: Injection molding deformation is not a single material issue, but rather result of combined effects of materials, structure, mold, process, and environment. Before mold opening, assessment and simulation should be used to reduce risks; after mold opening, data closed-loop analysis should be used to pinpoint cause, and it cannot be simply solved by "adding glass fiber".
Applicable Scenarios: Large-size PP/ABS/PC-ABS injection molded shells, bases, brackets, smart pet hardware, home appliances, robot structural components.
Core Concept: Injection molding deformation is not a single material issue, but rather result of combined effects of materials, structure, mold, process, and environment. Before mold opening, assessment and simulation should be used to reduce risks; after mold opening, data closed-loop analysis should be used to pinpoint cause, and it cannot be simply solved by "adding glass fiber".
1. First, understand: Why do injection molded parts deform?
Injection molded part deformation is essentially due to inconsistent shrinkage, cooling, and stress release in different areas within part. This can be simply understood as follows:
Molten plastic enters mold: Different flow paths at different locations; Different cooling rates at different locations; Different shrinkage rates at different locations; Different internal residual stresses; Warping, twisting, and bending occur after demolding/placement/high temperature.
Essence of injection molded part deformation: inconsistent shrinkage and stress release in different areas.
Molten plastic enters mold: Different flow paths at different locations; Different cooling rates at different locations; Different shrinkage rates at different locations; Different internal residual stresses; Warping, twisting, and bending occur after demolding/placement/high temperature.
Essence of injection molded part deformation: inconsistent shrinkage and stress release in different areas.
Key engineering judgment: Identify "which area shrinks differently and which type of stress is being released."
Common manifestations include: Planar warping; Diagonal twisting; Local bulging; Edge lifting; Misalignment of assembly holes; Unable to close cover; Deformation worsens after high-temperature storage; Appears OK at room temperature, but deformation is obvious after high temperature.
For large-sized exterior parts, such as litter box tops, bases, litter compartments, waste collection compartments, and large covers, risk of deformation is particularly high because of large part size, long flow length, varied wall thickness, numerous ribs, and many assembly constraints.
Common manifestations include: Planar warping; Diagonal twisting; Local bulging; Edge lifting; Misalignment of assembly holes; Unable to close cover; Deformation worsens after high-temperature storage; Appears OK at room temperature, but deformation is obvious after high temperature.
For large-sized exterior parts, such as litter box tops, bases, litter compartments, waste collection compartments, and large covers, risk of deformation is particularly high because of large part size, long flow length, varied wall thickness, numerous ribs, and many assembly constraints.
2. Deformation problems cannot be solved by simply asking "Is it a material problem?"
Deformation is usually not caused by a single factor. It is recommended to use extended version 5M1E for analysis.
| Dimensions | Focus Points | Examples of Injection Molding Deformation |
| Man | Machine adjustment capability, operational consistency | Differences in deformation between day and night shifts |
| Machine | Injection molding machine, mold, hot runner, cooling | Uneven mold cooling, unreasonable gate |
| Material | Raw materials, masterbatch, recycled materials, batches | High shrinkage rate, insufficient rigidity, batch fluctuations |
| Method | Injection molding parameters, inspection methods, work processes | Insufficient holding pressure, short cooling time, inconsistent measurement methods |
| Environment | Temperature and humidity, warehousing, transportation | Warping after 70℃ high-temperature storage |
| Measurement | Measuring tools, jigs, measurement benchmarks | Inconsistent flatness measurements by different engineers |
| Design | Wall thickness, ribs, fillets, assembly constraints | Sudden changes in wall thickness, excessively thick ribs, localized tensile stress |
| Supplier | Capabilities of material suppliers, mold manufacturers, and injection molding plants | Insufficient cooling design by mold manufacturers, inaccurate material supplier recommendations |
For new product development, especially in EVT/DVT stage, it is recommended to examine Design and Supplier separately. Many root causes of deformation are already present before mold opening and cannot be solved by injection molding plants simply by adjusting machines.
Deformation attribution: Material is only one factor.
Deformation attribution: Material is only one factor.
Conclusion: First establish measurement benchmarks and deformation patterns, then determine whether problem stems from materials, structure, mold, process, or assembly.
3. Before Mold Opening: How to Assess Deformation Risk
Period before mold opening is optimal stage for controlling deformation. Goal at this stage is not to completely eliminate risk, but to identify high-risk structures in advance.
3.1 First, Consider Product Form
Following parts are naturally more prone to deformation:
3.1 First, Consider Product Form
Following parts are naturally more prone to deformation:
| Part Characteristics | Deformation Risk |
| Large size, thin wall thickness | High |
| Long strip shape, thin plate shape | High |
| Large flat surface parts | High |
| Dense ribs on one side, empty on the other side | High |
| Locally thick glue, dense pillars | High |
| Gate can only be placed in an eccentric position | High |
| Requires high-temperature storage or overseas transportation | High |
| Constrained after assembly, many screws | High |
For products like cat litter boxes, typical high-risk parts include: Large exterior parts of upper shell; Large flat parts of base; Purchase compartment shell; Poop collection drawer; Large cover plate; Large area surrounding panel. These parts must undergo a specific deformation assessment before mold opening.
4. Before Mold Opening: How to Reduce Deformation in Structural Design
4.1 Uniform Wall Thickness
Uneven wall thickness is one of core sources of deformation and shrinkage.
Common Mistakes: Locally thick plastic areas: Slow cooling; Large shrinkage; Pulling out surrounding areas; Shrinkage or warping
Recommendations: Maintain a consistent main wall thickness as much as possible; Avoid sudden changes from 2.0 mm to 4.0 mm; Prioritize hollowing out, reducing plastic content, and modifying ribs in thick plastic areas; Control thickness of pillars and ribs on the back of exterior surface.
Common Experience: Rib thickness ≈ 0.5~0.6 times main wall thickness; Reduce plastic content and round corners at the base of pillars; Reinforce thick plastic areas with ribs, rather than directly thickening them.
4.2 Symmetrical, Continuous, and Balanced Ribs
More ribs are not necessarily better. Too many ribs or unilateral concentration will lead to uneven shrinkage.
Recommendations: Use a uniform rib mesh on the back of large flat surfaces; Avoid having dense ribs on one side and completely empty ribs on the other; Direction of ribs should be coordinated with main stress and flow directions as much as possible; Avoid strong pulling on one side around critical assembly areas.
4.3 Ensure sufficient rounding and transitions.
Sharp corners cause stress concentration, which is easily released after demolding and at high temperatures.
Recommendations: Use rounded transitions at wall thickness changes; Use rounded corners at the base of pillars and clips; Avoid sharp transitions at large flat corners.
4.4 Consider assembly constraints in advance.
Many deformations are not caused by the free state of individual parts, but by forced constraints after assembly.
For example: Slight deformation of a single part: Forcefully tightening screws during assembly; Increased internal stress; Released at high temperatures; More obvious deformation or cracking.
Recommendations: Allow some slack in assembly holes of large parts; Avoid forcibly flattening large areas of shell with screws; Define acceptable clearances for critical mating surfaces. Leave space for dimensional changes after high temperatures around moving parts.
Uneven wall thickness is one of core sources of deformation and shrinkage.
Common Mistakes: Locally thick plastic areas: Slow cooling; Large shrinkage; Pulling out surrounding areas; Shrinkage or warping
Recommendations: Maintain a consistent main wall thickness as much as possible; Avoid sudden changes from 2.0 mm to 4.0 mm; Prioritize hollowing out, reducing plastic content, and modifying ribs in thick plastic areas; Control thickness of pillars and ribs on the back of exterior surface.
Common Experience: Rib thickness ≈ 0.5~0.6 times main wall thickness; Reduce plastic content and round corners at the base of pillars; Reinforce thick plastic areas with ribs, rather than directly thickening them.
4.2 Symmetrical, Continuous, and Balanced Ribs
More ribs are not necessarily better. Too many ribs or unilateral concentration will lead to uneven shrinkage.
Recommendations: Use a uniform rib mesh on the back of large flat surfaces; Avoid having dense ribs on one side and completely empty ribs on the other; Direction of ribs should be coordinated with main stress and flow directions as much as possible; Avoid strong pulling on one side around critical assembly areas.
4.3 Ensure sufficient rounding and transitions.
Sharp corners cause stress concentration, which is easily released after demolding and at high temperatures.
Recommendations: Use rounded transitions at wall thickness changes; Use rounded corners at the base of pillars and clips; Avoid sharp transitions at large flat corners.
4.4 Consider assembly constraints in advance.
Many deformations are not caused by the free state of individual parts, but by forced constraints after assembly.
For example: Slight deformation of a single part: Forcefully tightening screws during assembly; Increased internal stress; Released at high temperatures; More obvious deformation or cracking.
Recommendations: Allow some slack in assembly holes of large parts; Avoid forcibly flattening large areas of shell with screws; Define acceptable clearances for critical mating surfaces. Leave space for dimensional changes after high temperatures around moving parts.
5. Before Mold Opening: How to Reduce Deformation in Mold Design
5.1 Gate Location Should Serve Shrinkage Balance
Gate determines flow direction, as well as molecular orientation, filling balance, and weld line location.
An unreasonable gate can lead to: Excessive unilateral shrinkage; Diagonal distortion; Weld lines falling in critical positions; Insufficient pressure transfer; Stress whitening near gate.
Before mold opening, following should be reviewed:
Gate determines flow direction, as well as molecular orientation, filling balance, and weld line location.
An unreasonable gate can lead to: Excessive unilateral shrinkage; Diagonal distortion; Weld lines falling in critical positions; Insufficient pressure transfer; Stress whitening near gate.
Before mold opening, following should be reviewed:
| Item | Focus Point |
| Number of gates | Will single-point injection cause long flow lines and unevenness? |
| Gate location | Is it eccentric, leading to excessive unilateral orientation? |
| Gate type | Are point gates, side gates, submarine gates, and hot runners suitable? |
| Weld line location | Does it fall on appearance surface, clips, screw pillars, or stress areas? |
| Pressure holding path | Is far end prone to insufficient pressure holding? |
For large-sized appearance parts, balanced injection should usually be prioritized, rather than just minimizing gate marks.
5.2 Cooling water channels are core of deformation control
Uneven cooling is one of main sources of deformation.
Before mold opening, pay close attention to following: Does water channel cover large flat areas? Is there localized cooling in thick plastic areas? Is temperature difference between moving and fixed molds controllable? Are there any cooling blind spots in deep cavity areas? Is there localized overheating near hot runners? Is cooling symmetrical? Many large parts deform, and subsequent machine adjustments are difficult to resolve because mold cooling system inherently introduces uneven cooling.
5.3 Ejection system must not cause secondary deformation.
Uneven ejection can cause parts to deform immediately after exiting mold.
Recommendations: Ejector pins should be evenly distributed; Avoid excessively strong ejection in large flat areas; Avoid strong ejection near weak edges and clips; Use combinations of push plates, ejector sleeves, and lifters when necessary.
5.4 Adequate venting is essential.
Poor venting can cause localized burning, weak weld lines, unstable filling, and amplified deformation.
Before mold making, following should be reviewed: End venting; Venting at weld lines; Venting in densely packed rib areas; Venting in deep cavity areas.
5.2 Cooling water channels are core of deformation control
Uneven cooling is one of main sources of deformation.
Before mold opening, pay close attention to following: Does water channel cover large flat areas? Is there localized cooling in thick plastic areas? Is temperature difference between moving and fixed molds controllable? Are there any cooling blind spots in deep cavity areas? Is there localized overheating near hot runners? Is cooling symmetrical? Many large parts deform, and subsequent machine adjustments are difficult to resolve because mold cooling system inherently introduces uneven cooling.
5.3 Ejection system must not cause secondary deformation.
Uneven ejection can cause parts to deform immediately after exiting mold.
Recommendations: Ejector pins should be evenly distributed; Avoid excessively strong ejection in large flat areas; Avoid strong ejection near weak edges and clips; Use combinations of push plates, ejector sleeves, and lifters when necessary.
5.4 Adequate venting is essential.
Poor venting can cause localized burning, weak weld lines, unstable filling, and amplified deformation.
Before mold making, following should be reviewed: End venting; Venting at weld lines; Venting in densely packed rib areas; Venting in deep cavity areas.
6. Before mold making: Material evaluation, whether to add glass fiber
6.1 First determine if part is suitable for glass fiber
Glass fiber can improve rigidity and reduce overall shrinkage, but it can also cause directional shrinkage, visible fiber shedding, reduced weld line strength, and mold wear. Therefore, whether to add glass fiber depends first on the type of part.
Glass fiber can improve rigidity and reduce overall shrinkage, but it can also cause directional shrinkage, visible fiber shedding, reduced weld line strength, and mold wear. Therefore, whether to add glass fiber depends first on the type of part.
| Part Type | Is Fiberglass PP Recommended? | Reason |
| Internal Support | Yes | Low appearance requirements, significant rigidity benefits |
| Motor Mount, Load-Bearing Mount | Yes | Requires rigidity and strength |
| Small Structural Parts | Can be evaluated | Small size, controllable directional risk |
| Base (Non-Appearance Area) | Caution | Requires evaluation of flow direction and warping |
| Large-Area Exterior Shell | Not Recommended Priority | High risk of floating fibers, flow marks, and directional deformation |
| Large-Area Thin-Wall Parts | Not Recommended for Direct Use of High Fiberglass | Easily prone to twisting and weld line issues |
| Parts with High Appearance Requirements | Generally Not Recommended | High surface risk |
6.2 How to Initially Determine Fiberglass Addition Amount
The higher proportion of fiberglass, the higher rigidity and the lower shrinkage, but the stronger directionality, the more difficult it is to control appearance, and the higher risk of weld lines.
The higher proportion of fiberglass, the higher rigidity and the lower shrinkage, but the stronger directionality, the more difficult it is to control appearance, and the higher risk of weld lines.
| Fiberglass Ratio | Features | Recommended Uses |
| GF5 | Slightly reinforced, lower risk | Slightly improves rigidity, appearance risk still needs verification |
| GF10 | Medium to low reinforcement, directionality begins to be obvious | Internal support, small structural components |
| GF15 | Significantly improved rigidity, obvious warpage directionality | Internal load-bearing components, mold flow verification required |
| GF20 | High rigidity, higher risk of appearance and warpage | Brackets, motor mounts, non-appearance load-bearing components |
| GF30 | High strength and high rigidity, obvious directionality and wear | Engineering structural components, not recommended for direct use in large appearance components |
For large litter box shells that are already mainly made of PP appearance components, if there is indeed suspicion of insufficient rigidity before mold making, fiberglass PP should not be the first choice. Instead, following should be evaluated first: PP + Talc T15/T20; PP + Talc + Toughening System; Low warpage, high rigidity PP. These materials have better dimensional stability and are more suitable for large-area appearance components than fiberglass.
6.3 When to Consider Fiberglass Before Mold Opening
Fiberglass can be considered as a candidate when following conditions are met: Part is an internal structural component; Appearance requirements are low; Main risk is insufficient rigidity or load-bearing capacity; Weld line is not in a critical stress area; Mold can be designed with gates and cooling systems for fiberglass; Supplier can provide similar case studies; Mold flow analysis shows controllable warpage. If these conditions are not met, fiberglass is not recommended as the first choice.
6.4 Mold Flow Analysis is Essential for Fiberglass Evaluation Before Mold Opening
Flow direction of fiberglass material must be carefully considered because fiberglass will orient itself along flow direction.
Molten Flow Direction: → → → → → →; Fiberglass Orientation Direction: → → → → →; Small shrinkage in flow direction; Large shrinkage perpendicular to direction; → Anisotropic shrinkage; → May lead to twisting deformation
Mold flow analysis should at least consider: Fill balance; Flow direction; Fiberglass orientation; Weld line location; Shrinkage distribution; Warpage direction; Pressure distribution; Cooling uniformity. Without mold flow analysis, directly deciding to add fiberglass to large parts carries a high risk.
6.3 When to Consider Fiberglass Before Mold Opening
Fiberglass can be considered as a candidate when following conditions are met: Part is an internal structural component; Appearance requirements are low; Main risk is insufficient rigidity or load-bearing capacity; Weld line is not in a critical stress area; Mold can be designed with gates and cooling systems for fiberglass; Supplier can provide similar case studies; Mold flow analysis shows controllable warpage. If these conditions are not met, fiberglass is not recommended as the first choice.
6.4 Mold Flow Analysis is Essential for Fiberglass Evaluation Before Mold Opening
Flow direction of fiberglass material must be carefully considered because fiberglass will orient itself along flow direction.
Molten Flow Direction: → → → → → →; Fiberglass Orientation Direction: → → → → →; Small shrinkage in flow direction; Large shrinkage perpendicular to direction; → Anisotropic shrinkage; → May lead to twisting deformation
Mold flow analysis should at least consider: Fill balance; Flow direction; Fiberglass orientation; Weld line location; Shrinkage distribution; Warpage direction; Pressure distribution; Cooling uniformity. Without mold flow analysis, directly deciding to add fiberglass to large parts carries a high risk.
7. Pre-Mold Opening: Recommended Material Evaluation Path
For large-size PP parts, recommended material selection order is as follows:
First Priority: Low-shrinkage PP from the same material system; Second Priority: PP + Talc T15/T20; Third Priority: PP + Talc + Toughening System; Fourth Priority: Low-warpage, high-stiffness PP; Fifth Priority: Glass fiber PP for local internal structural parts; Sixth Priority: Cross-material systems, such as ABS, PC/ABS
During material evaluation, suppliers should provide:
First Priority: Low-shrinkage PP from the same material system; Second Priority: PP + Talc T15/T20; Third Priority: PP + Talc + Toughening System; Fourth Priority: Low-warpage, high-stiffness PP; Fifth Priority: Glass fiber PP for local internal structural parts; Sixth Priority: Cross-material systems, such as ABS, PC/ABS
During material evaluation, suppliers should provide:
| Data | Purpose |
| TDS/Material Property Table | Initial performance assessment |
| Shrinkage data | Assess mold compatibility risks |
| CAE Material Card | For mold flow analysis |
| Recommended processing window | Assess mass production process difficulty |
| High-temperature aging data | Assess long-term performance retention |
| Similar large-size appearance part examples | Assess application maturity |
| Color masterbatch and color scheme | Assess appearance and batch stability |
8. Pre-Mold Opening: What should DFM/Mold Flow Review output be?
Deformation assessment before mold opening should not remain a verbal discussion but must be documented. Suggested Outputs:
| Output Items | Content |
| Deformation Risk List | Which parts and areas may deform? |
| Material Candidate List | Candidates include PP, PP-T20, toughened PP, and fiberglass PP. |
| Mold Flow Analysis Report | Filling, holding pressure, cooling, warpage, and weld lines. |
| Gate Review Conclusion | Are number, location, and form of gates confirmed? |
| Cooling Review Conclusion | Does cooling system cover high-risk areas? |
| Structural Modification Suggestions | Reduce material usage, add stiffeners, uniform wall thickness, and optimize corner radius. |
| Verification Plan | How to measure and determine deformation after T0/T1. |
The most important question before mold opening is: Is this deformation risk addressed through material selection, structural design, mold design, or process design? If this question is not clearly answered, subsequent mold trials can easily lead to repeated machine adjustments.
9. After Mold Opening: When deformation is discovered, the first step is not to change materials.
When deformation is discovered after mold opening, the first step is not to immediately change materials or add fiberglass, but to establish baseline data.
9.1 First, confirm deformation type
9.1 First, confirm deformation type
| Type | Typical Manifestation | Possible Direction |
| Overall Warping | The entire plane bends upwards/downwards | Cooling, shrinkage, insufficient rigidity |
| Diagonal Twisting | Corners are not coplanar | Gate eccentricity, uneven flow, uneven orientation |
| Local Bulging | Protrusion near thick plastic areas or pillars | Wall thickness, holding pressure, cooling |
| Edge Warping | Warping around frame or opening | Uneven structure, uneven cooling, demolding stress |
| Deformation after High Temperature | OK at room temperature, deformed after high temperature | Residual stress release, material heat resistance, structural release |
| Deformation after Assembly | OK for a single piece, abnormal after assembly | Assembly stress, hole constraints, screw locking sequence |
9.2 Record Baseline Data
At least record: Material Batch; Masterbatch; Whether recycled material was added; Injection Molding Machine; Mold Number/Cavity; Material Temperature, Mold Temperature; Injection Speed; Holding Pressure; Holding Time; Cooling Time; Cycle; Exit Temperature; Measurement Time Point; Deformation Amount and Flatness; Dimensional Changes Before and After High Temperature. Without this data, subsequent discussions are basically guesswork.
At least record: Material Batch; Masterbatch; Whether recycled material was added; Injection Molding Machine; Mold Number/Cavity; Material Temperature, Mold Temperature; Injection Speed; Holding Pressure; Holding Time; Cooling Time; Cycle; Exit Temperature; Measurement Time Point; Deformation Amount and Flatness; Dimensional Changes Before and After High Temperature. Without this data, subsequent discussions are basically guesswork.
10. Post-Mold Opening: Handle Deformation Using "Four-Step Method"
It is recommended to handle deformation in following order:
Step 1: Measurement and Cause Attribution; Step 2: Process Window Optimization; Step 3: Mold Correction; Step 4: Material Change.
Step 1: Measurement and Cause Attribution; Step 2: Process Window Optimization; Step 3: Mold Correction; Step 4: Material Change.
Do not change materials immediately. Material changes should generally be done after initial troubleshooting of process and mold issues.
11. Step 1: Measurement and Cause Attribution
11.1 Measurement Must Be Consistent
Deformation measurement should be defined as: Measurement reference plane; Measurement point; Part placement state; Measurement time point; Whether measured in free state; Whether measured in assembled state; How long after high temperature recovery should measurement be performed?
It is recommended to measure at least three time points: 2 hours after demolding; 24 hours after demolding; After 70℃×72h, 4 hours after room temperature recovery.
Many PP parts continue to shrink after demolding, so measuring only dimensions immediately after demolding is unreliable.
11.2 Determining if the Problem is Material, Mold, or Process
Deformation measurement should be defined as: Measurement reference plane; Measurement point; Part placement state; Measurement time point; Whether measured in free state; Whether measured in assembled state; How long after high temperature recovery should measurement be performed?
It is recommended to measure at least three time points: 2 hours after demolding; 24 hours after demolding; After 70℃×72h, 4 hours after room temperature recovery.
Many PP parts continue to shrink after demolding, so measuring only dimensions immediately after demolding is unreliable.
11.2 Determining if the Problem is Material, Mold, or Process
| Phenomenon | More Likely Cause |
| Deformation in same direction in every mold | Mold/Structure/Gate/Cooling Issues |
| Large differences between different machines | Equipment or process window issues |
| Large batch fluctuations for same parameter | Material batch or process stability issues |
| Significant deformation after high temperature | Residual stress, material heat resistance, structural release |
| Shrinkage in areas far from gate | Insufficient pressure transfer or wall thickness issues |
| Cracks near weld lines | Gate, venting, material temperature, material toughness issues |
12. Second Step: Process Optimization
Process optimization is the fastest way to improve after mold opening, but it has its limits. Structural and cooling design errors cannot be masked by machine adjustments in long term.
12.1 Common Machine Adjustment Directions
12.1 Common Machine Adjustment Directions
| Process Item | Potential Impact |
| Increase mold temperature | Improve weld lines and surface finish, but may increase cycle time |
| Optimize material temperature | Improve flow and pressure transfer; excessively high temperatures may increase shrinkage and decomposition |
| Increase holding pressure | Improve shrinkage and dimensions, but may increase internal stress |
| Extend holding pressure time | Improve far-end shrinkage compensation, but ineffective after gate freezing |
| Extend cooling time | Reduce demolding deformation, but increase cycle time. |
| Adjust injection speed | Improve flow marks, weld lines, shearing, and orientation. |
| Lower demolding temperature | Reduce post-demolding deformation. |
12.2 Note: Higher holding pressure is not always better.
Insufficient holding pressure will cause shrinkage, but excessive holding pressure may lead to: Increased internal stress; Gate whitening; Difficult demolding; Stress release deformation after high temperature; Cracking of clips or screw posts. Therefore, process optimization should not only focus on whether surface is flat immediately after demolding, but also on whether it stabilizes after high temperature.
Insufficient holding pressure will cause shrinkage, but excessive holding pressure may lead to: Increased internal stress; Gate whitening; Difficult demolding; Stress release deformation after high temperature; Cracking of clips or screw posts. Therefore, process optimization should not only focus on whether surface is flat immediately after demolding, but also on whether it stabilizes after high temperature.
13. Step Three: Mold Correction
When deformation has a fixed direction, fixed area, and fixed pattern, mold correction is usually required.
13.1 Common Mold Improvement Measures
13.1 Common Mold Improvement Measures
| Measures | Applicable Problems |
| Adjust cooling water channels | Uneven cooling, localized hot spots |
| Increase localized cooling | Thick plastic areas, deep cavity areas, near hot runners |
| Modify gate | Uneven filling, insufficient holding pressure, poor weld line location |
| Increase/adjust venting | End burning, weak weld line, unstable filling |
| Adjust ejection | Ejection deformation, edge deformation |
| Correct steel material compensation | Stable deformation dimensional compensation |
| Optimize rib area corresponding to mold | Shrinkage, localized stretching |
13.2 Confirm Stability Before Mold Repair
Before mold repair, following must be confirmed: Stable deformation direction; Stable deformation amount; Process window basically confirmed; No abnormalities in material batches; Consistent measurement methods. If deformation itself is unstable, blindly repairing mold may lead to more problems.
Before mold repair, following must be confirmed: Stable deformation direction; Stable deformation amount; Process window basically confirmed; No abnormalities in material batches; Consistent measurement methods. If deformation itself is unstable, blindly repairing mold may lead to more problems.
14. Step Four: Material Change
Material change is an effective means, but it must be selected according to the objective.
| Current Issues | Material Direction |
| High-Temperature Deformation | High-Stiffness, Low-Shrinkage, Talc-Filled PP |
| Drop Cracking | Toughened PP, PP+EPDM/POE |
| Significant Shrinkage | Low-Shrinkage PP, PP-T15/T20 |
| Flow Marks | More Suitable Flowability, Low Fiber Float System |
| Weak Weld Lines | High-Flowability, High-Toughness System, Combined with Mold Venting |
| Snap-in Whitening | Toughened System, Reduces Local Stress |
For large-size PP exterior parts, it is recommended to prioritize: PP + Talc T15/T20; PP + Talc + Toughened System; Low Warpage, High-Stiffness PP. Instead of directly using glass fiber.
15. Can Adding Glass Fiber Solve Deformation?
15.1 What Can Glass Fiber Solve?
Glass Fiber Can Bring: Increased Stiffness; Increased Heat Deformation Temperature; Reduced Shrinkage in Flow Direction; Increased Load-Bearing Capacity. If current deformation mainly comes from insufficient part stiffness, and part is an internal structural component, glass fiber may be effective.
15.2 What New Problems Might Bring About Fiberglass?
If mold is already made and deformation has already occurred, directly adding fiberglass may bring more complex problems.
Glass Fiber Can Bring: Increased Stiffness; Increased Heat Deformation Temperature; Reduced Shrinkage in Flow Direction; Increased Load-Bearing Capacity. If current deformation mainly comes from insufficient part stiffness, and part is an internal structural component, glass fiber may be effective.
15.2 What New Problems Might Bring About Fiberglass?
If mold is already made and deformation has already occurred, directly adding fiberglass may bring more complex problems.
| Risks | Explanation |
| Directional Shrinkage | Shrinkage in flow direction differs from that perpendicular to flow direction, potentially causing distortion. |
| Change in Deformation Direction | What was originally upward-curved may become diagonally distorted. |
| Weld Line Weakening | Fiberglass may have difficulty crossing weld line, potentially causing cracking upon drop. |
| Surface Fiber Floating | Surface defects such as mottled appearance, flow marks, and roughness appear on large exterior parts. |
| Increased Molding Pressure | Mold filling becomes more difficult, and adjustment window narrows. |
| Mold Wear | Increased wear on gates, runners, cavities, and screws. |
| Decreased Drop Toughness | Increased rigidity but also increased brittleness, especially in notched areas. |
Therefore, when deformation has already been detected, fiberglass is not the first choice.
15.3 If You Must Try Fiberglass, How Should You Try It?
Do not try GF30 directly. Small-scale, layered comparisons are recommended.
15.3 If You Must Try Fiberglass, How Should You Try It?
Do not try GF30 directly. Small-scale, layered comparisons are recommended.
| Candidate | Purpose |
| Current Material | Benchmark |
| PP-T20 Talc | Dimensional Stability Comparison |
| PP-T20 Toughening | Comprehensive Performance Comparison |
| PP-GF10 | Low Proportion Glass Fiber Risk Verification |
| PP-GF20 | Higher Rigidity Upper Limit Verification |
Required Tests: Initial Dimensions; Flatness/Warpage; Appearance; Weld Lines; Assembly; 70℃×72h; Return to Room Temperature; Dimensional Remeasurement; High Temperature Drop
Key Observations: Does deformation truly decrease? Does deformation direction change? Does diagonal twist worsen? Are weld lines obvious? Does weld line drop cause cracking? Is there any fiber floating on appearance? Are injection pressure and cycle acceptable?
Key Observations: Does deformation truly decrease? Does deformation direction change? Does diagonal twist worsen? Are weld lines obvious? Does weld line drop cause cracking? Is there any fiber floating on appearance? Are injection pressure and cycle acceptable?
16. Recommended Path for Large PP Parts for Cat Litter Boxes
For products like cat litter boxes, especially when mold is already made, PP is currently used, and deformation is found, it is recommended to converge along following path: Establish current material and process benchmarks; Clarify deformation type and measurement method; Optimize Injection Molding Process Window; Check Mold Cooling, Gate, Venting, and Ejection; Try Low-Shrinkage PP from Same Material System; Try PP-T15/T20 with Talc Reinforcement; Try Talc + Toughening Balancing Material; Evaluate GF10/GF20 for Internal Structural Components; Avoid Direct Switching to GF30 for Large Exterior Parts; Perform Assembly and Drop Testing After High-Temperature Storage
Priority Recommendations:
Priority Recommendations:
| Priority | Solution | Description |
| 1 | Process Window Optimization | Fastest, Lowest Cost |
| 2 | Cooling and Gate Review | Deformation Root Causes Often Lie in Mold |
| 3 | Low-Shrinkage PP from Same Material System | Low Risk of Matching with Existing Molds |
| 4 | PP-T15/T20 | Common Direction for Stable Large Part Dimensions |
| 5 | PP-Talc + Toughening | Balances High Temperature, Dimensions, and Drop Tests |
| 6 | Partial Glass Fiber PP | Suitable for Internal Structures, Not Prioritized for Large Exterior Parts |
| 7 | Major Mold Modification or Cross-Material System | Highest Cost and Risk |
17. Decision Matrix: Should Glass Fiber Be Added?
This matrix can be used to determine whether to add glass fiber before or after mold opening.
| Judgment Item | Ye s | No |
| Is part an internal component or a part with low appearance requirements? | Bonus Points | Deduction Points |
| Is main problem insufficient rigidity? | Bonus Points | Deduction Points |
| Has mold flow analysis been performed and glass fiber orientation confirmed to be controllable? | Bonus Points | Deduction Points |
| Does weld line avoid critical stress areas? | Bonus Points | Deduction Points |
| Is mold designed according to glass fiber wear and flowability? | Bonus Points | Deduction Points |
| Can risk of surface fiber floating and flow marks be accepted? | Bonus Points | Deduction Points |
| Is drop not a core risk? | Bonus Points | Deduction Points |
| Does the supplier have similar application cases? | Bonus Points | Deduction Points |
Deduction Suggested Judgment:
Mostly "Yes": Can be included as a candidate; About half "Yes": Only perform small-scale verification; direct import is not recommended; Mostly "No": Glass fiber solution is not recommended
Mostly "Yes": Can be included as a candidate; About half "Yes": Only perform small-scale verification; direct import is not recommended; Mostly "No": Glass fiber solution is not recommended
18. Final Judgment Criteria for Deformation Issues
It is recommended not to simply write "no obvious deformation," but to quantify it.
| Item | Suggested Judgment Method |
| Flatness | ≤ X mm |
| Diagonal Difference | ≤ X mm |
| Critical Gap | ≤ X mm |
| Hole Position Deviation | ≤ X mm |
| Permanent Deformation After High Temperature | ≤ X mm |
| Assembly | No interference, no forced assembly, no gaps |
| Motion Function | No jamming, no abnormal noise, no abnormal friction |
| Appearance | No obvious shrinkage, warping, whitening, or worsening of flow marks |
| Drop Test | No cracks after high-temperature drop, normal function |
For overseas products, it is recommended to define at least: 70℃×72h: Room temperature recovery 4h; Dimensional remeasurement; Assembly verification; Functional verification; Drop test. For new materials or major mold modifications, stringency can be increased to: 70℃*168h.
19. Summary
Injection molding deformation issues should be handled separately before and after mold opening.
Before mold making, key points are: Uniform structure, balanced gates, sufficient cooling, material matching, mold flow verification, and proactive risk management. After mold making, key points are: Measure first, then attribute causes; prioritize process, then mold, then materials, and only consider major modifications last.
Regarding fiberglass, core conclusion is: Fiberglass can improve rigidity, but it cannot be simply equated with "solving deformation." It introduces directional shrinkage, weld lines, appearance issues, wear, and drop risks. Before mold making, it is essential to analyze part type, flow direction, and mold flow to determine suitability. If deformation has already occurred after mold making, it is not recommended to directly address problem by adding fiberglass, especially for large-area shells with high appearance requirements.
For large PP exterior structural components like cat litter boxes, a more reliable material approach is typically: Low-shrinkage PP from the same system: PP + talc T15/T20; PP + talc + toughening system; Local evaluation of internal structural components using fiberglass PP. Ultimate goal is not to find the "hardest material," but rather to find a solution that balances deformation, appearance, drop resistance, and cost within existing structural, mold, process, and reliability requirements.
Before mold making, key points are: Uniform structure, balanced gates, sufficient cooling, material matching, mold flow verification, and proactive risk management. After mold making, key points are: Measure first, then attribute causes; prioritize process, then mold, then materials, and only consider major modifications last.
Regarding fiberglass, core conclusion is: Fiberglass can improve rigidity, but it cannot be simply equated with "solving deformation." It introduces directional shrinkage, weld lines, appearance issues, wear, and drop risks. Before mold making, it is essential to analyze part type, flow direction, and mold flow to determine suitability. If deformation has already occurred after mold making, it is not recommended to directly address problem by adding fiberglass, especially for large-area shells with high appearance requirements.
For large PP exterior structural components like cat litter boxes, a more reliable material approach is typically: Low-shrinkage PP from the same system: PP + talc T15/T20; PP + talc + toughening system; Local evaluation of internal structural components using fiberglass PP. Ultimate goal is not to find the "hardest material," but rather to find a solution that balances deformation, appearance, drop resistance, and cost within existing structural, mold, process, and reliability requirements.


