T-slot Driven Slider Design

Time:2026-11-21 08:56:55 / Popularity: / Source:

T-slot driven slider designs are often used for core pulling of fixed mold sliders and moving mold sliders in small spaces, and can also be used for core pulling of large inclined sliders. When slider width is large, it is difficult to balance slider movement using a single inclined guide post, and it is difficult to achieve consistency with two or more inclined guide posts. In this case, using a T-slot driven slider is the best choice.

1. T-slot Driven Slider Saves Space

Upper shell of controller is shown in Figure 9-46. Small end of plastic part is a square box with round holes on the side, requiring a fixed mold slider core pulling design. Top surface of large end is inclined, with 5 inclined pillar holes, requiring a fixed mold inclined slider core pulling design, driven by a T-slot.
T-slot Driven Slider Design 
T-slot Driven Slider Design 
Figure 9-46 T-slot driven front mold inclined slider core pulling
1 - Bent pin; 2 - Fixed mold base plate; 3 - Runner ejector plate; 4 - T-shaped inclined wedge; 5 - Limiting block; 6 - Spring; 7 - Inclined slider; 8 - Slider insert; 14 - Slider insert; 9 - Plate A; 10 - Cavity; 11 - Core; 12 - Moving mold insert; 13 - Plate B; 16 - Fixed mold slider; 17 - Limiting pin

2. T-slot Driven Multiple Slider Design

The largest water cup product has a maximum external dimension of 145mm x 190mm, as shown in Figure 9-47. Plastic part is large, with 8 sliders of different sizes, and mold design arranges them in a 1-to-1 configuration. Gating system is designed with a large sprue. Molten plastic enters parting surface through sprue bushing and then flows into mold along three side sprues of inner hole.
As shown in diagram, cup-shaped plastic part has three ribs on outer circumference of small end and one external threaded through-hole post; small end of the inner hole has three discontinuous threads, requiring a small slider core-pulling design; large end of inner hole has two snap-fit positions, requiring an internal slider core-pulling design; shape of plastic part requires a large, half-slider forming design. Difficulty in mold design lies in interlacing and positional interference of inner and outer sliders. Three internal sliders 4 at small end of plastic part are driven by T-slots, with sprue bushing also acting as a scraper. Slider slots are located within fixed mold insert 3, guided and clamped by pressure blocks. Small threaded hole slider 7 on the side of fixed mold is driven by a hydraulic cylinder. Outer diameter of this thread is formed by two large, half-slider shapes. Two large, half-slider shapes 13 are moving mold sliders, avoiding interference with two inner sliders 24. To improve mold-closing accuracy of two large sliders 13, two sets of circular tapered locating blocks are designed on their mating surfaces. Due to large height of these two half-slider blocks, guide strip 11 (pressure strip) must be designed at waist of slider and fixed to plate B 12 with screws. Because of limited space, this slider is driven by a wedge 29 via a T-block 28. Half-slider is limited by a spring 36 and a spring-loaded screw 37. Inner slider 24 is driven by an inner slider bent pin 23; this slider is smaller and is sandwiched between two large half-slider blocks.
Due to special shape of plastic part, ejector pins cannot be used for ejection; therefore, four push blocks 32 are used for ejection at the edge of plastic part. Since push blocks are at the bottom of slider, a reset mechanism is required. Central runner push rod 21 is mounted on push rod pad 22; therefore, after push plate 19 has ejected 12mm, push rod pad 22 breaks off central sprue material via push rod 21, achieving automatic separation of gate and plastic part within mold.
T-slot Driven Slider Design 
T-slot Driven Slider Design 
T-slot Driven Slider Design 
Figure 9-47 Large Water Cup Mold Diagram 1 - Sprue Bushing; 2, 28 - T-blocks; 3 - Fixed Mold Insert; 4, 24 - Inner Slider; 5 - Fixed Mold Base Plate; 6 - Plate A; 7 - Threaded Hole Slider Insert; 8 - Cylinder Seat; 9 - Cylinder; 10 - Conical Positioning Block; 11 - Slider Guide Strip; 12 - Plate B; 13 - Moving Mold Large Slider; 14 - Moving Mold Pad; 15 - Core; 16, 25, 36 - Spring; 17 - Spring Guide Rod; 18 - Ejector Rod Fixing Plate; 19 - Ejector Plate; 20 - Moving Mold Base Plate; 21 - Runner Ejector Rod; 22 - Ejector Rod Pad; 23 - Inner Slider Bend Pin; 26 - Reset Rod; 27, 30 - Wear-resistant Plate; 29 - Wedge; 31 - Limit Screw; 32 - Ejector Block; 33 - Screw; 34 - Ejector Rod; 35 - Limit Switch; 37 - Spring Pressing Screw

3. Complex T-Slot Driven Slider Design

Toy birdhouse plastic part, as shown in Figure 9-48, measures 327mm x 145mm x 160mm, is made of ABS, weighs 0.525kg, and has an average wall thickness of 4.5mm. It has one lug and three wire clips on each of its two sloping sides, all requiring inclined slider molding. Two elongated holes are located on a triangular plane on the back of part, also necessitating a slider core-pulling mechanism. As this is an exterior part, gate cannot be designed on the outer surface. Difficulty in mold design lies in three lateral core-pulling mechanisms, selecting a suitable gating method, and eliminating impact of thermal expansion on lateral core-pulling mechanisms.
Two lugs and three wire clips on the left and right sides of molded part will inevitably create slider weld lines, affecting part's appearance. Analysis suggests that slider parting surface should be located at its highest point.
T-slot Driven Slider Design 
After analyzing structure of plastic part, mold requires three large sliders for core pulling. To reduce mold size and make it suitable for production with a 3x10N injection molding machine, core pulling mechanism uses a T-slot to drive sliders, and mold structure is designed as an inverted structure. Moving platen is designed as an integral set structure to provide sufficient locking force for three sliders. Ejection of plastic part is designed with ejector tubes and ejector rods, all mounted on ejector plate. Ejection mechanism of inverted mold is usually driven by a hydraulic cylinder. Hydraulic cylinder piston rod is connected to fixed mold base plate 14 via hydraulic cylinder piston joint 13, and hydraulic cylinder body is connected to ejector rod fixing plate 11. Mold opening and closing mechanism is controlled by pull mold buckle 29, and stroke limit is achieved by limit screw 31. Ejection and return of ejector plate are monitored by limit switches 23 and 25. A support head 24 is designed at the bottom of core fixing plate 8, and a hot nozzle sleeve 16 is designed at the center of mold to increase rigidity of core fixing plate. Wear-resistant plates are designed at the bottom and on inclined surface of large slider 22. Structure of large slider is shown in mold drawing. Core 7 is assembled on core fixing plate 8, and core 7 is clamped by clamping blocks 32 and 33. Mold design adopts Longji mold base, model GCH-5060-A210-B150-C200-L450 simplified point gate mold base.
T-slot Driven Slider Design 
T-slot Driven Slider Design 
After mold opening, driven by injection molding moving platen, mold moving mold base plate 1 retracts, separating from moving platen 2. Driven by guide slider 3, two inclined sliders 5 move obliquely to detach from plastic part. After opening 60mm, under action of limit screw 31, moving platen 2 retracts with moving mold base plate 1, pull mold buckle 29 opens, main parting surface of mold opens, and under action of inclined guide post 20, large slider 22 completes lateral core pulling. Hydraulic cylinder on push plate drives push plate to eject plastic part through push rod and push tube.
T-slot Driven Slider Design 
Figure 9-48 Toy Birdhouse Mold Diagram
1 - Moving mold base plate; 2 - Moving mold plate; 3 - Guide slider; 4 - Pad block; 5 - Inclined slider; 6 - Reset rod; 7 - Core; 8 - Core fixing plate; 9 - Hydraulic cylinder; 10 - Pad block; 11 - Push rod fixing plate; 12 - Push plate; 13 - Hydraulic cylinder piston joint; 14 - Fixed mold base plate; 15 - Push rod; 16 - Hot nozzle sleeve; 17 - Hot nozzle; 18 - Push plate guide post; 19 - Inclined guide post fixing plate; 20 - Inclined guide post; 21 - Wear-resistant plate; 22 - Large slider; 23, 25 - Limit switch; 24 - Support head; 26 - Push tube; 27 - Moving mold insert; 28 - Guide post; 29 - Pull mold buckle; 30 - Locking module; 31 - Limit screw; 32, 33 - Clamping block
Mold structure design is novel, mechanism operates smoothly and flexibly. After mold opens, inclined slider stays on moving mold side, plastic part remains on fixed mold side, hydraulic cylinder ejects smoothly and stably, making it easy for robot to remove plastic part, thus enabling fully automated production.

Go To Top