Adjustment of Back Pressure in Injection Molding Process
Time:2026-11-21 08:24:45 / Popularity: / Source:
Back pressure (also known as plasticizing pressure) refers to pressure exerted on melt in storage area at the front of screw head when screw rotates and retracts. When screw rotates, heated and molten plastic is pushed forward, passing through gap in stop ring (rubber ring, spacer) to reach storage chamber in front of screw. As melt is continuously pushed forward, pressure is generated in this area, acting on screw and stop ring, pushing them backward to allow more space to accommodate more melt. For hydraulic injection molding machines, retraction of screw pushes piston of connected injection cylinder backward, hydraulic oil in rear chamber of cylinder flows back to injection molding machine's oil tank via oil pipe. When speed of hydraulic oil return is controlled, a resistance affecting screw's retraction will be generated in rear chamber of cylinder; this resistance is called back pressure. The greater speed limit of return pressure oil, the greater resistance generated in rear chamber of cylinder, that is, the greater back pressure. Figure 2-4.
Figure 2-4 Schematic diagram of hydraulic back pressure
Back pressure adjustment of a hydraulic injection molding machine is very easy during material storage process; different back pressure values can be set at different screw positions. However, for fully electric injection molding machines, back pressure control is more complex. When screw rotates, back pressure setting (via a load device or converter) generates resistance on pressure bearing. Value of this resistance is a function of servo motor's rotational speed; the higher back pressure value, the greater resistance. For fully electric injection molding machines, back pressure can be called resistance-sensing back pressure.
Back pressure adjustment of a hydraulic injection molding machine is very easy during material storage process; different back pressure values can be set at different screw positions. However, for fully electric injection molding machines, back pressure control is more complex. When screw rotates, back pressure setting (via a load device or converter) generates resistance on pressure bearing. Value of this resistance is a function of servo motor's rotational speed; the higher back pressure value, the greater resistance. For fully electric injection molding machines, back pressure can be called resistance-sensing back pressure.
(1) Functions of back pressure
It generates sufficient mechanical energy to melt and mix plastic during plasticizing. It removes volatile gases, including air, from barrel. It uniformly mixes additives (such as color powder, pigments, antistatic agents, talc, etc.) with molten material. It homogenizes molten material flowing through different screw lengths. It provides a uniform and stable plasticizing material, ensuring precise control of finished product weight.
(2) Back Pressure Adjustment
Back pressure adjustment for injection molding should be determined based on properties of raw materials, their drying conditions, product structure, and its quality. During normal production, back pressure is generally set between 3-15 kg/cm². When product surface has slight air bubbles, color mixing, shrinkage, or significant changes in product size and weight, back pressure can be appropriately increased. Excessive back pressure can easily lead to following problems:
High melt pressure at barrel tip, high melt temperature, decreased viscosity increase backflow of melt in screw channel and leakage flow between barrel and screw, reducing plasticizing efficiency (amount of material plasticized per unit time). For plastics with poor thermal stability (such as PVC, POM, etc.) or colorants, increased temperature of melt leads to longer heating time in barrel, causing thermal decomposition, or increased color change in colorant, resulting in poorer surface color/gloss of product. Excessive back pressure slows screw retraction, prolongs pre-plasticizing return time, increases cycle time, and leads to decreased production efficiency. High back pressure leads to high melt pressure, causing molten material to flow into mold runner, clogging nozzle or resulting in cold slug spots in product during injection molding. During pre-plasticizing, excessive back pressure can cause leakage at nozzle, resulting in material waste and burnout of heating coil near nozzle. High back pressure increases mechanical wear on screw and barrel.
When nozzle leakage, drooling, overheating and decomposition of melt, product discoloration, and slow material return occur, back pressure can be appropriately reduced. Too low a back pressure can easily lead to following problems: With too low a back pressure, screw retracts too quickly, resulting in low-density (loose) melt flowing into the front of barrel, trapping more air. This leads to poor plasticizing quality, unstable injection volume, and significant variations in product weight and dimensions. Surface defects such as shrinkage, air bubbles, cold slug marks, and uneven gloss may appear on product surface. Air bubbles are prone to appear inside product, and material shortages are likely to occur around product edges and ribs.
High melt pressure at barrel tip, high melt temperature, decreased viscosity increase backflow of melt in screw channel and leakage flow between barrel and screw, reducing plasticizing efficiency (amount of material plasticized per unit time). For plastics with poor thermal stability (such as PVC, POM, etc.) or colorants, increased temperature of melt leads to longer heating time in barrel, causing thermal decomposition, or increased color change in colorant, resulting in poorer surface color/gloss of product. Excessive back pressure slows screw retraction, prolongs pre-plasticizing return time, increases cycle time, and leads to decreased production efficiency. High back pressure leads to high melt pressure, causing molten material to flow into mold runner, clogging nozzle or resulting in cold slug spots in product during injection molding. During pre-plasticizing, excessive back pressure can cause leakage at nozzle, resulting in material waste and burnout of heating coil near nozzle. High back pressure increases mechanical wear on screw and barrel.
When nozzle leakage, drooling, overheating and decomposition of melt, product discoloration, and slow material return occur, back pressure can be appropriately reduced. Too low a back pressure can easily lead to following problems: With too low a back pressure, screw retracts too quickly, resulting in low-density (loose) melt flowing into the front of barrel, trapping more air. This leads to poor plasticizing quality, unstable injection volume, and significant variations in product weight and dimensions. Surface defects such as shrinkage, air bubbles, cold slug marks, and uneven gloss may appear on product surface. Air bubbles are prone to appear inside product, and material shortages are likely to occur around product edges and ribs.
(3) Application of Multi-Stage Back Pressure
Regarding effective plasticizing length of screw, since screw rotates and retracts simultaneously during material storage stage, we can imagine that length of screw from its end to feed inlet is different at the beginning and end of material storage. Screw length is longest at the beginning of storage and shortest at the end. Plastic entering screw channel at different times also travels different lengths through screw, resulting in varying shear energy. This difference causes unevenness in melt temperature (i.e., viscosity) within storage chamber, thus affecting instability of product quality during injection molding.
The longer screw stroke, the greater variation in effective plasticizing length, and the greater resulting instability. If different and increasing back pressure values are used at different screw retraction positions during material storage, melt temperature differences caused by above phenomenon can be effectively reduced, making production process more stable. Following methods for setting screw parameters can be used as a reference: In last 10-15% of feed stroke, increase back pressure and decrease screw rotation speed, controlling screw overshoot distance to 0.2-0.4mm. Achieving optimal combination of screw speed and back pressure requires experimentation. For example: Start screw at optimal surface speed. Melt back pressure value is 5-7 bar. Optimal screw surface speed for a specific plastic can be found in Table 2-3. When screw feed stroke is 25% and 60% complete, increase melt back pressure to 10 bar and 12 bar respectively; keep screw speed unchanged to reduce variations caused by different effective screw lengths. When screw feed stroke is 85% complete, further increase melt back pressure to 15 bar and halve screw speed to reduce screw overshoot. When screw stops rotating, retract screw by 5mm (reverse screwing or extraction).
The longer screw stroke, the greater variation in effective plasticizing length, and the greater resulting instability. If different and increasing back pressure values are used at different screw retraction positions during material storage, melt temperature differences caused by above phenomenon can be effectively reduced, making production process more stable. Following methods for setting screw parameters can be used as a reference: In last 10-15% of feed stroke, increase back pressure and decrease screw rotation speed, controlling screw overshoot distance to 0.2-0.4mm. Achieving optimal combination of screw speed and back pressure requires experimentation. For example: Start screw at optimal surface speed. Melt back pressure value is 5-7 bar. Optimal screw surface speed for a specific plastic can be found in Table 2-3. When screw feed stroke is 25% and 60% complete, increase melt back pressure to 10 bar and 12 bar respectively; keep screw speed unchanged to reduce variations caused by different effective screw lengths. When screw feed stroke is 85% complete, further increase melt back pressure to 15 bar and halve screw speed to reduce screw overshoot. When screw stops rotating, retract screw by 5mm (reverse screwing or extraction).
Last article:Cooling System Design
Next article:T-slot Driven Slider Design

