Sharing 15 Rotary Sliding Rack Core-Pulling Mold Design Structures
Time:2026-11-16 09:14:53 / Popularity: / Source:
Core of rotary sliding rack core-pulling mold lies in using rack and pinion transmission to convert linear motion into rotational motion, solving problems such as rounded undercuts, multi-directional holes, or threads on product side that cannot be demolded using ordinary inclined guide pillars. So-called "15 structures" do not refer to 15 completely different principles, but rather to 15 specific engineering implementation schemes formed by different driving methods, transmission stages, and layouts in typical scenarios such as 15 sliders simultaneously performing rounded core pulling.
Following are 15 variations of rotary sliding rack core-pulling design structure compiled based on classic industry cases: Core Transmission and Drive Combination Structure
1. Direct-drive rack and pinion type: Piston rod of a hydraulic/pneumatic cylinder is directly connected to a long rack. Rack meshes with a large central gear, which drives 15 peripheral sliders to rotate synchronously. Suitable for peripheral core-pulling with large stroke and uniform force.
2. Spring preload reset type: A strong spring is added to rear end of rack. When mold opens, cylinder pulls rack to pull core; when mold closes, spring force pushes rack back to its original position. This simplifies hydraulic control circuit, is suitable for small to medium tonnage molds.
3. Double rack symmetrical drive type: A rack is set on each side of gear, and they are synchronously pulled by same cylinder through a connecting rod. This eliminates gear wobble caused by unilateral force and improves synchronization accuracy of 15 slider movements.
4. Angled pin assisted rotation type: Rack drives gear to rotate. An angled pin is installed on gear shaft and inserts into slider's angled groove, converting rotational motion into slider's arc trajectory, increasing motion stability.
5. Hydraulic motor indirect drive type: Output shaft of hydraulic motor is connected to a small gear. Small gear meshes with a large gear ring (or rack) to achieve speed reduction and torque increase. This is suitable for core pulling of high-resistance threads or deep cavities.
Slider Layout and Motion Trajectory Variations
6. 15-Slider Type with Evenly Divided Circumference: 360° is divided into 15 equal parts (24° each). Sliders move along arc guide rail. Release angle of each slider needs to be accurately calculated to avoid interference.
7. Non-Evenly Divided Angle Adaptive Type: For products with uneven hole distribution, gear sets or eccentric racks with different numbers of teeth are customized to allow 15 sliders to rotate and demold in different proportions.
8. Double-Layer Nested Rotation Type: Outer ring large slider drives inner ring small slider to rotate. Rack drives outer layer, and inner layer achieves differential rotation through secondary gear transmission. This is used for complex impeller structures.
9. Segmented Arc Guide Rail: Slider guide rail is divided into two arcs with different radii of curvature. Rack drive allows for rapid disengagement in initial stage and slow, precise positioning in later stage, reducing impact.
10. Center Insert Retracts First: Before mold opening, center insert retracts 3-5mm to relieve product's tension on gate. Then, rack and pinion mechanism drives 15 slides to rotate, preventing damage to gate.
Special Functions and Auxiliary Mechanisms
11. Ejector Pin Linkage Positioning: Ejector plate is fixed to B-plate via a pull rod. Initially, it moves 5mm with B-plate to maintain product positioning. After slides are fully withdrawn, ejector pins eject product, solving problem of product sticking to mold.
12. Anti-Rotation Structure: An anti-rotation pin is installed on non-core-pulling surface of product. Combined with rack and pinion mechanism, it ensures that product only exits axially and does not rotate with core, specifically for unscrewed structures.
13. Cooling Water Channel Follow-up: Rotating slides integrate a follow-up cooling connector. Cooling water channel is simultaneously connected when rack and pinion move, solving heat dissipation problem of rotating parts.
14. Limiting and Buffering Protection Type: A hydraulic buffer or rubber buffer block is installed at the end of rack stroke to prevent rigid impact when all 15 sliders are in position simultaneously, extending mold life.
15. Modular Quick-Change Rack Assembly: Rack and slider are designed as independent modules, connected via a standard interface. When product hole position is finely adjusted, only rack needs to be replaced or gear ratio adjusted, without remaking the entire mold base.
1. Direct-drive rack and pinion type: Piston rod of a hydraulic/pneumatic cylinder is directly connected to a long rack. Rack meshes with a large central gear, which drives 15 peripheral sliders to rotate synchronously. Suitable for peripheral core-pulling with large stroke and uniform force.
2. Spring preload reset type: A strong spring is added to rear end of rack. When mold opens, cylinder pulls rack to pull core; when mold closes, spring force pushes rack back to its original position. This simplifies hydraulic control circuit, is suitable for small to medium tonnage molds.
3. Double rack symmetrical drive type: A rack is set on each side of gear, and they are synchronously pulled by same cylinder through a connecting rod. This eliminates gear wobble caused by unilateral force and improves synchronization accuracy of 15 slider movements.
4. Angled pin assisted rotation type: Rack drives gear to rotate. An angled pin is installed on gear shaft and inserts into slider's angled groove, converting rotational motion into slider's arc trajectory, increasing motion stability.
5. Hydraulic motor indirect drive type: Output shaft of hydraulic motor is connected to a small gear. Small gear meshes with a large gear ring (or rack) to achieve speed reduction and torque increase. This is suitable for core pulling of high-resistance threads or deep cavities.
Slider Layout and Motion Trajectory Variations
6. 15-Slider Type with Evenly Divided Circumference: 360° is divided into 15 equal parts (24° each). Sliders move along arc guide rail. Release angle of each slider needs to be accurately calculated to avoid interference.
7. Non-Evenly Divided Angle Adaptive Type: For products with uneven hole distribution, gear sets or eccentric racks with different numbers of teeth are customized to allow 15 sliders to rotate and demold in different proportions.
8. Double-Layer Nested Rotation Type: Outer ring large slider drives inner ring small slider to rotate. Rack drives outer layer, and inner layer achieves differential rotation through secondary gear transmission. This is used for complex impeller structures.
9. Segmented Arc Guide Rail: Slider guide rail is divided into two arcs with different radii of curvature. Rack drive allows for rapid disengagement in initial stage and slow, precise positioning in later stage, reducing impact.
10. Center Insert Retracts First: Before mold opening, center insert retracts 3-5mm to relieve product's tension on gate. Then, rack and pinion mechanism drives 15 slides to rotate, preventing damage to gate.
Special Functions and Auxiliary Mechanisms
11. Ejector Pin Linkage Positioning: Ejector plate is fixed to B-plate via a pull rod. Initially, it moves 5mm with B-plate to maintain product positioning. After slides are fully withdrawn, ejector pins eject product, solving problem of product sticking to mold.
12. Anti-Rotation Structure: An anti-rotation pin is installed on non-core-pulling surface of product. Combined with rack and pinion mechanism, it ensures that product only exits axially and does not rotate with core, specifically for unscrewed structures.
13. Cooling Water Channel Follow-up: Rotating slides integrate a follow-up cooling connector. Cooling water channel is simultaneously connected when rack and pinion move, solving heat dissipation problem of rotating parts.
14. Limiting and Buffering Protection Type: A hydraulic buffer or rubber buffer block is installed at the end of rack stroke to prevent rigid impact when all 15 sliders are in position simultaneously, extending mold life.
15. Modular Quick-Change Rack Assembly: Rack and slider are designed as independent modules, connected via a standard interface. When product hole position is finely adjusted, only rack needs to be replaced or gear ratio adjusted, without remaking the entire mold base.
Design Key Considerations
Angle Calculation: If 15 sliders rotate synchronously, rotation angle of a single slider is usually 360°/15 = 24°. Rack stroke needs to be calculated by reverse calculation based on actual release distance (circumference = π × diameter × angle / 360).
Clearance Control: A clearance of 0.05-0.1mm needs to be reserved between gear and rack meshing, a double-lead gear is used to eliminate backlash and prevent slider wobbling.
Lubrication and Maintenance: Automatic oil injection holes must be designed for rotating parts. Due to high-frequency rotation, wear is easily caused. It is recommended to use grease containing molybdenum disulfide. Upper structure needs to be verified through motion simulation in software such as UG/NX using specific product 3D data, with a focus on checking interference zone and synchronization. In practical applications, hydraulic cylinder direct drive or motor drive can be selected according to mold space constraints, prioritizing synchronization accuracy and rigidity of 15 slider movements.
Angle Calculation: If 15 sliders rotate synchronously, rotation angle of a single slider is usually 360°/15 = 24°. Rack stroke needs to be calculated by reverse calculation based on actual release distance (circumference = π × diameter × angle / 360).
Clearance Control: A clearance of 0.05-0.1mm needs to be reserved between gear and rack meshing, a double-lead gear is used to eliminate backlash and prevent slider wobbling.
Lubrication and Maintenance: Automatic oil injection holes must be designed for rotating parts. Due to high-frequency rotation, wear is easily caused. It is recommended to use grease containing molybdenum disulfide. Upper structure needs to be verified through motion simulation in software such as UG/NX using specific product 3D data, with a focus on checking interference zone and synchronization. In practical applications, hydraulic cylinder direct drive or motor drive can be selected according to mold space constraints, prioritizing synchronization accuracy and rigidity of 15 slider movements.

