Design of a Template-Driven Automatic Unscrewing Injection Mold for a Liquid Collector
Time:2026-11-16 08:40:03 / Popularity: / Source:
Abstract: A template-driven automatic unscrewing injection mold for a liquid collector with a large-pitch trapezoidal double-threaded internal part was designed to address this issue. To improve anti-rotation capability of plastic part during internal thread core pulling, 48 arc-shaped straight-line structures and 4 trapezoidal reinforcing ribs were added circumferentially to plastic part. Internal thread core pulling mechanism utilizes mold opening force to drive gear shaft, which rotates round nut and transmits rotation to gear, thereby achieving rotational release of internal thread core from fixed mold core insert. A precision positioning component and an elastic clamping assembly are added to end of internal threaded core, along with an venting device, to ensure a tight fit between internal threaded core, fixed mold core insert, and surface of plastic part, effectively improving molding quality and reliability of internal threaded core pulling. Based on molding performance of medical-grade transparent polycarbonate and high surface quality requirements of medical device components, a "two-point eight-cavity" (two hot nozzles, eight cavities) hot runner combined with a cold runner gating system with a submarine gate is adopted. Its feasibility was verified using Moldflow 2026 software, ensuring product molding quality and shortening development cycle. Simultaneously, four sets of fixed-distance parting mechanisms are set up to gradually separate moving mold part, part of fixed mold structure, and hot runner system components before internal threaded core is pulled out, ensuring smooth and efficient removal of internal threaded core and fixed mold core insert. Production practice shows that this mold structure is compact, its operation is reliable, and product quality is stable.
When injection molding plastic parts with internal threads, two common methods are forced demolding and rotary demolding. The former is prone to product deformation and is only suitable for specific applications; the latter can achieve automatic removal of internal thread core, with stable and reliable quality, and is therefore widely used. Literature review shows that a wealth of research results have been achieved regarding rotary demolding. Wang Jing, Rong Xing, Chen Yazhou, Zhang Yun et al. used hydraulic motors as power sources and adopted gear transmission, screw and nut transmission, sprocket transmission to drive internal thread core to rotate and demold. Chen Jianling, Li Bo et al. used motor drive and achieved internal thread self-rotation demolding through sprocket or gear mechanism. Peng Shiyan, Wang Jianwu et al. used hydraulic cylinder to drive rack and drive internal thread core to automatically eject. Wang Genhua, Yu Wei, Yue Qiang used mold opening force and drove gear rotation through worm rotation or rack movement to complete demolding. It can be seen that commonly used power sources for rotary demolding are hydraulic motor, motor, hydraulic cylinder and mold opening force. Transmission mechanism can be selected from one or more combinations of gear rack, worm gear, chain sprocket, synchronous belt, nut and screw. Selection of power source and design of transmission mechanism are two major research hotspots in this field. The first three power sources are external power sources, characterized by high driving force and good demolding effect, but with complex mold structures. They are suitable for large or precision plastic parts with high demolding force requirements and complex movements. Mold opening force comes from injection molding machine itself, which is an internal power source. Its demolding force is smaller, but corresponding mold structure is compact and production cost is low. It is suitable for small and medium-sized threaded plastic parts with simple structures and low demolding force requirements. However, current research on structural form, fixing method, motion type of internal threaded cores is insufficient, and related discussions are rare. In fact, specific structure, positioning and installation method, realization form of rotation and movement of internal threaded core are key factors determining demolding quality. In-depth research on these aspects will effectively improve design level of internal threaded core-pulling mechanisms. Therefore, this paper takes a liquid collector product as an example to discuss structure and demolding method of its internal threaded core and designs the entire injection mold, aiming to provide a reference for production practice.
When injection molding plastic parts with internal threads, two common methods are forced demolding and rotary demolding. The former is prone to product deformation and is only suitable for specific applications; the latter can achieve automatic removal of internal thread core, with stable and reliable quality, and is therefore widely used. Literature review shows that a wealth of research results have been achieved regarding rotary demolding. Wang Jing, Rong Xing, Chen Yazhou, Zhang Yun et al. used hydraulic motors as power sources and adopted gear transmission, screw and nut transmission, sprocket transmission to drive internal thread core to rotate and demold. Chen Jianling, Li Bo et al. used motor drive and achieved internal thread self-rotation demolding through sprocket or gear mechanism. Peng Shiyan, Wang Jianwu et al. used hydraulic cylinder to drive rack and drive internal thread core to automatically eject. Wang Genhua, Yu Wei, Yue Qiang used mold opening force and drove gear rotation through worm rotation or rack movement to complete demolding. It can be seen that commonly used power sources for rotary demolding are hydraulic motor, motor, hydraulic cylinder and mold opening force. Transmission mechanism can be selected from one or more combinations of gear rack, worm gear, chain sprocket, synchronous belt, nut and screw. Selection of power source and design of transmission mechanism are two major research hotspots in this field. The first three power sources are external power sources, characterized by high driving force and good demolding effect, but with complex mold structures. They are suitable for large or precision plastic parts with high demolding force requirements and complex movements. Mold opening force comes from injection molding machine itself, which is an internal power source. Its demolding force is smaller, but corresponding mold structure is compact and production cost is low. It is suitable for small and medium-sized threaded plastic parts with simple structures and low demolding force requirements. However, current research on structural form, fixing method, motion type of internal threaded cores is insufficient, and related discussions are rare. In fact, specific structure, positioning and installation method, realization form of rotation and movement of internal threaded core are key factors determining demolding quality. In-depth research on these aspects will effectively improve design level of internal threaded core-pulling mechanisms. Therefore, this paper takes a liquid collector product as an example to discuss structure and demolding method of its internal threaded core and designs the entire injection mold, aiming to provide a reference for production practice.
1 Plastic Part Structure Optimization
Figure 1a shows initial 3D model of blood collection device provided to customer. This plastic part is a supporting product for a medical device, and material is medical-grade transparent polycarbonate (PC). During operation, trapezoidal double-threaded internal part at small end of plastic part connects to medical device's transmission mechanism. Centrifugal force separates impurities from blood, enabling blood separation, storage, recovery during surgery. Therefore, trapezoidal double-threaded internal part is both an important structural feature and a key indicator of its molding quality. Plastic part is basin-shaped, possessing a natural center of rotation. It is prone to rotation when disengaging from internally threaded core, affecting molding quality; therefore, an anti-rotation structure is necessary. The most effective method in production practice is to add anti-rotation structures to inner and outer surfaces of plastic part, fully utilizing its inherent structural characteristics. To this end, after communication with customer, it was decided to evenly distribute 48 arc-shaped straight-line structures (3 mm radius, 0.2 mm depth) on outer ring of large end of plastic part, evenly place 4 trapezoidal reinforcing ribs (0.36 mm width, 0.5 mm height) on inner wall. Synergistic effect of inner and outer surfaces significantly improves anti-rotation capability of plastic part. Optimized 3D model of product is shown in Figure 1b.
Fig. 1 3D drawing of liquid collector product
1—Trapezoidal double-start internal thread; 2—Arc-shaped straight knurl; 3—Reinforcing rib
Fig. 2 is a 2D drawing of optimized plastic part. The overall dimensions of plastic part are Ø50.1 mm * 29.98 mm. Inner surface of small end has a Tr13 trapezoidal double-start internal thread with a pitch of 4 mm, a thread length of 13.71 mm, and a minor diameter of Ø11 mm. Wall thickness of plastic part varies considerably: center of small end is a hollow conical structure with a wall thickness of only 0.94 mm; while the thickest part at outer rounded corners reaches 4.1 mm. As a transparent medical device accessory, safety is paramount; outer surface of plastic part must be smooth and flat, without sharp protrusions, dents, flash, or other molding defects.
1—Trapezoidal double-start internal thread; 2—Arc-shaped straight knurl; 3—Reinforcing rib
Fig. 2 is a 2D drawing of optimized plastic part. The overall dimensions of plastic part are Ø50.1 mm * 29.98 mm. Inner surface of small end has a Tr13 trapezoidal double-start internal thread with a pitch of 4 mm, a thread length of 13.71 mm, and a minor diameter of Ø11 mm. Wall thickness of plastic part varies considerably: center of small end is a hollow conical structure with a wall thickness of only 0.94 mm; while the thickest part at outer rounded corners reaches 4.1 mm. As a transparent medical device accessory, safety is paramount; outer surface of plastic part must be smooth and flat, without sharp protrusions, dents, flash, or other molding defects.
Fig. 2 2D drawing of liquid collector product after structural optimization
2 Mold structure design
2.1 Analysis of key points of mold design
(1) Overall layout. As required by customer, mold adopts an eight-cavity layout. In order to facilitate smooth release of internal thread core, mold opening direction is selected to be vertical direction of plastic part axis, that is, large end plane (basin opening is downward) is main parting surface. Correspondingly, internal thread core pulling mechanism must be set in fixed mold part.
(2) Design of gating system. PC has a high melting temperature, high viscosity and poor fluidity. It requires a high temperature and pressure during injection molding. It is advisable to use a hot runner system . At the same time, as a transparent medical device accessory, surface quality of plastic part is extremely high. There must be no gate marks to prevent skin punctures during use. Therefore, only point gates or submarine gates can be used, solidified material of gating system should be easy to remove. Since an internal thread core-pulling mechanism needs to be set at small end, a point gate cannot be arranged. Therefore, gating system can only be set in moving mold part. Considering all factors, it was decided to use hot runner to cold runner method to introduce melt into cavity. Given large difference in wall thickness of plastic part and complex structure at small end thread, it is easy to have insufficient filling. It is necessary to use Moldflow software to analyze, determine gate position and gating system structure, verify its rationality.
(3) Demolding system design. Plastic part needs to be equipped with both an internal thread automatic core-pulling mechanism and a plastic part ejection mechanism. Double-line trapezoidal internal thread of plastic part is a large pitch thread (13.71 mm long, 8 mm lead). It only needs to be rotated 1.71 times to be ejected. Required demolding force is small and suitable for template drive scheme. In addition, plastic part has an external dimension of Ø50.1 mm*29.98 mm, which is a small plastic part, which also meets application of template drive. Therefore, mold opening force is selected as power source to drive internal thread core to rotate and demold, so as to simplify mold structure and reduce production cost. Because bottom of plastic part is ring-shaped and wall thickness is small, it is impossible to install push rods or ejector tubes, so a push plate is used for ejection.
(4) Cooling system design. A hot runner system requires strict control of mold temperature. Various cooling devices, such as straight-through, ring-type, and baffle-type, should be comprehensively designed based on specific structure of molded parts.
(5) Injection molding machine selection. Density of PC plastic is 1.2 g/cm³, volume of a single plastic part is 8.589 cm³, and the total mass of eight plastic parts is 82.45 g. Considering melt volume required by gating system, it was decided to select customer's existing Haitian MA1200Ⅲ injection molding machine. This machine has a theoretical injection mass of 230 g, an injection pressure of 202 MPa, a clamping force of 1600 kN, a maximum mold thickness of 500 mm, and a mold travel of 400 mm.
(2) Design of gating system. PC has a high melting temperature, high viscosity and poor fluidity. It requires a high temperature and pressure during injection molding. It is advisable to use a hot runner system . At the same time, as a transparent medical device accessory, surface quality of plastic part is extremely high. There must be no gate marks to prevent skin punctures during use. Therefore, only point gates or submarine gates can be used, solidified material of gating system should be easy to remove. Since an internal thread core-pulling mechanism needs to be set at small end, a point gate cannot be arranged. Therefore, gating system can only be set in moving mold part. Considering all factors, it was decided to use hot runner to cold runner method to introduce melt into cavity. Given large difference in wall thickness of plastic part and complex structure at small end thread, it is easy to have insufficient filling. It is necessary to use Moldflow software to analyze, determine gate position and gating system structure, verify its rationality.
(3) Demolding system design. Plastic part needs to be equipped with both an internal thread automatic core-pulling mechanism and a plastic part ejection mechanism. Double-line trapezoidal internal thread of plastic part is a large pitch thread (13.71 mm long, 8 mm lead). It only needs to be rotated 1.71 times to be ejected. Required demolding force is small and suitable for template drive scheme. In addition, plastic part has an external dimension of Ø50.1 mm*29.98 mm, which is a small plastic part, which also meets application of template drive. Therefore, mold opening force is selected as power source to drive internal thread core to rotate and demold, so as to simplify mold structure and reduce production cost. Because bottom of plastic part is ring-shaped and wall thickness is small, it is impossible to install push rods or ejector tubes, so a push plate is used for ejection.
(4) Cooling system design. A hot runner system requires strict control of mold temperature. Various cooling devices, such as straight-through, ring-type, and baffle-type, should be comprehensively designed based on specific structure of molded parts.
(5) Injection molding machine selection. Density of PC plastic is 1.2 g/cm³, volume of a single plastic part is 8.589 cm³, and the total mass of eight plastic parts is 82.45 g. Considering melt volume required by gating system, it was decided to select customer's existing Haitian MA1200Ⅲ injection molding machine. This machine has a theoretical injection mass of 230 g, an injection pressure of 202 MPa, a clamping force of 1600 kN, a maximum mold thickness of 500 mm, and a mold travel of 400 mm.
2.2 Design of gating system
2.2.1 Selection of gate location
First, three-dimensional model of plastic part was completed in NX 12.0, STL format was exported and imported into Moldflow 2026. Double-layer mesh was used for division and repair. After selecting PC material of Trinseo and completing corresponding settings, "gate location" analysis was performed. Results are shown in Figure 3. Optimal gate location is located in annular area near cylinder on the surface of plastic part. This area is suitable for arranging point gates. However, since upper end of plastic part (fixed mold part) needs to be equipped with an internal thread core-pulling mechanism, it is not possible to arrange point gates in this recommended area.
First, three-dimensional model of plastic part was completed in NX 12.0, STL format was exported and imported into Moldflow 2026. Double-layer mesh was used for division and repair. After selecting PC material of Trinseo and completing corresponding settings, "gate location" analysis was performed. Results are shown in Figure 3. Optimal gate location is located in annular area near cylinder on the surface of plastic part. This area is suitable for arranging point gates. However, since upper end of plastic part (fixed mold part) needs to be equipped with an internal thread core-pulling mechanism, it is not possible to arrange point gates in this recommended area.
Figure 3 Gate matching analysis
Considering analysis results and actual production needs, it was decided to adopt a submarine gate and set it near large end surface. This scheme is not only convenient for arrangement of upper internal thread core-pulling mechanism, but also facilitates the overall ejection of plastic part by the template, thereby effectively improving molding quality. It should be noted that matching index of this submarine gate is only 0.2694 (see Figure 3), a relatively low value. Its feasibility still needs further verification through subsequent mold flow analysis to ensure final molding quality of plastic part.
2.2.2 Verification Analysis of Gating System
To verify feasibility of designed submarine gate, improve mold design quality, reduce trial molding and mold repair workload, gating system needs to be simulated and analyzed using Moldflow 2026 software. Results will be compared with recommended injection molding process parameters for PC. According to relevant literature, main injection molding process parameters for PC are as follows: mold temperature 80~120 ℃, injection pressure 80~180 MPa, holding pressure 40%~80% of injection pressure, injection cycle 40~120s, barrel temperature 230~320 ℃, and nozzle temperature 280~320 ℃. These parameters will serve as important evaluation criteria for injection molding analysis of plastic part.
First, a three-dimensional model of cold runner of gating system was constructed in NX 12.0. Main structural parameters were: main runner length 33 mm, small end diameter 3 mm, large end diameter 5 mm; branch runner with U-shaped cross section, width 5.2 mm, height 4 mm; branch runner length between two plastic parts 194 mm; submarine gate diameter 0.6 mm, gate centerline and plastic part axis angle 35°. After simplifying model, it was imported into Moldflow 2026, and double-layer mesh was used for generation and repair to obtain mesh data that met analysis requirements (number of nodes 90,928, average aspect ratio 2.02, matching percentage 85.7%). Then, "filling analysis" sequence was selected, and mold surface temperature was set to 100 ℃, melt temperature to 300 ℃, and injection pressure to 120 MPa in process settings, while the other parameters were kept at default values, and simulation analysis was performed. To comprehensively evaluate three major molding indicators of time, temperature and pressure, following six key indicators were selected from analysis results to evaluate feasibility of gating system: filling time, time to reach ejection temperature, flow front temperature, overall temperature at the end of filling, pressure at speed/pressure switching, and pressure at the end of filling. Specific analysis results are shown in Figure 4.
Considering analysis results and actual production needs, it was decided to adopt a submarine gate and set it near large end surface. This scheme is not only convenient for arrangement of upper internal thread core-pulling mechanism, but also facilitates the overall ejection of plastic part by the template, thereby effectively improving molding quality. It should be noted that matching index of this submarine gate is only 0.2694 (see Figure 3), a relatively low value. Its feasibility still needs further verification through subsequent mold flow analysis to ensure final molding quality of plastic part.
2.2.2 Verification Analysis of Gating System
To verify feasibility of designed submarine gate, improve mold design quality, reduce trial molding and mold repair workload, gating system needs to be simulated and analyzed using Moldflow 2026 software. Results will be compared with recommended injection molding process parameters for PC. According to relevant literature, main injection molding process parameters for PC are as follows: mold temperature 80~120 ℃, injection pressure 80~180 MPa, holding pressure 40%~80% of injection pressure, injection cycle 40~120s, barrel temperature 230~320 ℃, and nozzle temperature 280~320 ℃. These parameters will serve as important evaluation criteria for injection molding analysis of plastic part.
First, a three-dimensional model of cold runner of gating system was constructed in NX 12.0. Main structural parameters were: main runner length 33 mm, small end diameter 3 mm, large end diameter 5 mm; branch runner with U-shaped cross section, width 5.2 mm, height 4 mm; branch runner length between two plastic parts 194 mm; submarine gate diameter 0.6 mm, gate centerline and plastic part axis angle 35°. After simplifying model, it was imported into Moldflow 2026, and double-layer mesh was used for generation and repair to obtain mesh data that met analysis requirements (number of nodes 90,928, average aspect ratio 2.02, matching percentage 85.7%). Then, "filling analysis" sequence was selected, and mold surface temperature was set to 100 ℃, melt temperature to 300 ℃, and injection pressure to 120 MPa in process settings, while the other parameters were kept at default values, and simulation analysis was performed. To comprehensively evaluate three major molding indicators of time, temperature and pressure, following six key indicators were selected from analysis results to evaluate feasibility of gating system: filling time, time to reach ejection temperature, flow front temperature, overall temperature at the end of filling, pressure at speed/pressure switching, and pressure at the end of filling. Specific analysis results are shown in Figure 4.
Figure 4 Filling analysis
As can be seen from Figure 4, filling time of plastic part is 1.474 s, filling is balanced, and there are no short shots, delays and over-holding pressure phenomena. Time to reach ejection temperature is 88.72 s, which meets requirements of recommended injection cycle (≤120 s). Maximum flow front temperature is 300.8 ℃, and maximum overall temperature at the end of filling is 307.6 ℃. Temperature change of each plastic part is small, indicating that temperature distribution is uniform during filling process and there is no overheating phenomenon. Pressure at speed/pressure switching is 36.73 MPa, and pressure at the end of filling is 40.62 MPa. Cavity pressure is balanced and there is no area where actual injection pressure may be too high. In summary, designed gating system structure is reasonable and feasible. Final decision was to adopt a hybrid gating scheme combining a "two-point, eight-cavity" hot runner system with a cold runner system: molten plastic entering mold from injection molding machine is heated by hot runner plate, flows out through two needle valve hot nozzles, then enters eight cavities through runner insert, cold runner, and submarine gate.
As can be seen from Figure 4, filling time of plastic part is 1.474 s, filling is balanced, and there are no short shots, delays and over-holding pressure phenomena. Time to reach ejection temperature is 88.72 s, which meets requirements of recommended injection cycle (≤120 s). Maximum flow front temperature is 300.8 ℃, and maximum overall temperature at the end of filling is 307.6 ℃. Temperature change of each plastic part is small, indicating that temperature distribution is uniform during filling process and there is no overheating phenomenon. Pressure at speed/pressure switching is 36.73 MPa, and pressure at the end of filling is 40.62 MPa. Cavity pressure is balanced and there is no area where actual injection pressure may be too high. In summary, designed gating system structure is reasonable and feasible. Final decision was to adopt a hybrid gating scheme combining a "two-point, eight-cavity" hot runner system with a cold runner system: molten plastic entering mold from injection molding machine is heated by hot runner plate, flows out through two needle valve hot nozzles, then enters eight cavities through runner insert, cold runner, and submarine gate.
2.3 Design of Internal Thread Core-Pulling Mechanism
Essence of template-driven rotational demolding is to convert linear movement of template into rotation and axial movement of threaded core. The key is that plastic part remains stationary while internal threaded core rotates and retracts. Therefore, core of designing internal threaded core-pulling mechanism is to determine structural form and movement mode of internal threaded core.
2.3.1 Design of Internal Threaded Core Assembly
Small end of plastic part includes a Tr13 trapezoidal double-line internal thread and an adjacent hollow conical structure, which needs to be formed by internal threaded core and fixed mold core insert. During molding and demolding, both must move synchronously; otherwise, end molding quality will be affected. Figure 5 shows assembly of internal thread forming part after combining two components with product model.
2.3.1 Design of Internal Threaded Core Assembly
Small end of plastic part includes a Tr13 trapezoidal double-line internal thread and an adjacent hollow conical structure, which needs to be formed by internal threaded core and fixed mold core insert. During molding and demolding, both must move synchronously; otherwise, end molding quality will be affected. Figure 5 shows assembly of internal thread forming part after combining two components with product model.
Figure 5 Assembly for internal thread forming part
1—Product; 2—Fixed mould core insert; 3—Internal thread core
Figure 6 shows 3D model of fixed mould core insert and internal thread core part. To eliminate influence of negative pressure on molding process of plastic part end, improve quality of plastic part end and demolding effect, venting devices are set on the surfaces of both parts, including venting grooves 2 and 8, symmetrical venting platform 1, venting hole 7. To ensure synchronous movement of two parts, anti-rotation structure 3 and shoulder 6 are designed on their surfaces respectively. In addition, internal thread core is also provided with threaded hole 4 and keyway 5 for connecting axial precision positioning parts, elastic clamping components, and gears.
1—Product; 2—Fixed mould core insert; 3—Internal thread core
Figure 6 shows 3D model of fixed mould core insert and internal thread core part. To eliminate influence of negative pressure on molding process of plastic part end, improve quality of plastic part end and demolding effect, venting devices are set on the surfaces of both parts, including venting grooves 2 and 8, symmetrical venting platform 1, venting hole 7. To ensure synchronous movement of two parts, anti-rotation structure 3 and shoulder 6 are designed on their surfaces respectively. In addition, internal thread core is also provided with threaded hole 4 and keyway 5 for connecting axial precision positioning parts, elastic clamping components, and gears.
Figure 6 Fixed mould core insert and internal thread core
1—Symmetric venting platform; 2, 8—Venting groove; 3—Anti-rotation structure; 4—Thread hole; 5—Keyway; 6—Shaft shoulder; 7—Vent hole; 9—Thread
2.3.2 Design of Internal Thread Core Pulling Mechanism
To simultaneously eject eight plastic parts, the entire mold is equipped with eight sets of internal thread core assemblies and four sets of drive gear assemblies. Each set of drive gear assemblies drives two sets of internal thread core assemblies. During mold opening, template moves, causing gear shaft in drive gear assembly to move, forcing nut to rotate. Motion is transmitted to internal thread core assembly through gear transmission, achieving rotational ejection of fixed mold core insert from internal thread core.
Figure 7 shows a single set of internal thread core pulling mechanism, consisting of one drive gear assembly and two sets of internal thread core assemblies (only one set of internal thread core assemblies is shown in figure). Both gears are spur gears with a module of 1.5 mm, 56 teeth, and a center distance of 84 mm.
1—Symmetric venting platform; 2, 8—Venting groove; 3—Anti-rotation structure; 4—Thread hole; 5—Keyway; 6—Shaft shoulder; 7—Vent hole; 9—Thread
2.3.2 Design of Internal Thread Core Pulling Mechanism
To simultaneously eject eight plastic parts, the entire mold is equipped with eight sets of internal thread core assemblies and four sets of drive gear assemblies. Each set of drive gear assemblies drives two sets of internal thread core assemblies. During mold opening, template moves, causing gear shaft in drive gear assembly to move, forcing nut to rotate. Motion is transmitted to internal thread core assembly through gear transmission, achieving rotational ejection of fixed mold core insert from internal thread core.
Figure 7 shows a single set of internal thread core pulling mechanism, consisting of one drive gear assembly and two sets of internal thread core assemblies (only one set of internal thread core assemblies is shown in figure). Both gears are spur gears with a module of 1.5 mm, 56 teeth, and a center distance of 84 mm.
Fig. 7 Single internal thread core pulling mechanism
1—Drive gear assembly; 2—Internal thread core assembly
Fig. 8 shows drive gear assembly. Fig. 8a is a structural diagram of assembly, consisting of screws 1, 9, and 12, washers 2 and 11, gear shaft 3, bearings 4 and 7, gear 5, round nut 6, gear shaft fixing plate 8, gear shaft end cap 10, etc. Round nut 6 is screwed onto gear shaft 3 and supported in template by bearing. Round nut 6 and gear shaft 3 form a nut-screw pair, and gear 5, fixed to round nut 6 by a flat key, rotates together.
1—Drive gear assembly; 2—Internal thread core assembly
Fig. 8 shows drive gear assembly. Fig. 8a is a structural diagram of assembly, consisting of screws 1, 9, and 12, washers 2 and 11, gear shaft 3, bearings 4 and 7, gear 5, round nut 6, gear shaft fixing plate 8, gear shaft end cap 10, etc. Round nut 6 is screwed onto gear shaft 3 and supported in template by bearing. Round nut 6 and gear shaft 3 form a nut-screw pair, and gear 5, fixed to round nut 6 by a flat key, rotates together.
1,9, 12-Screw; 2, 11-Washer; 3-Gear shaft; 4,7-Bearing; 5-Gear;
6-Round nut; 8-Gear shaft clamping plate; 10-Gear shaft end cover
(a) Assembly structure drawing
1-First fixed mould plate; 2-Second fixed mould plate; 3-First fixed mould support plate; 4Bearing; 5-Gear shaft; 6-Round nut; 7-Gearshaft clamping plate; 8, 9-Gear; 10-Internal thread core; 11-Plastic part
(b) Drawing of automatic thread unscrewing
Fig. 8 Drive gear assembly
Fig. 8b is a schematic diagram of automatic unscrewing principle. Gear shaft 5 is fixed to first fixed mold support plate 3 by gear shaft fixing plate 7, and can only move, not rotate. When mold opens along parting surface III, gear shaft 5 moves together with second fixed mold plate 2 and first fixed mold support plate 3. At this point, plastic part 11 is fixed in cavity and cannot move. Movement force of mold opening forces internal thread of plastic part to rotate in helical direction. Therefore, round nut 6 rotates under support of bearing, driving gear 8 fixed on it to rotate, which in turn transmits motion to gear 9, driving internal thread core 10 to rotate, thus achieving automatic demolding of internal thread core.
Figure 9 shows internal thread core assembly, which consists of a fixed mold core insert 11, an internal thread core 12, plastic part 10, sliding bearings 5 and 9, rolling bearings 6 and 8, a gear 7, a set screw 4, a screw 3, an internal thread core end cap 2, and a spring 1. Internal thread core end cap 2, through screw 3, presses set screw 4 and spring 1 to end of internal thread core 12, improving fitting accuracy between set screw 4 and internal thread core 12, and achieving precise axial positioning.
(b) Drawing of automatic thread unscrewing
Fig. 8 Drive gear assembly
Fig. 8b is a schematic diagram of automatic unscrewing principle. Gear shaft 5 is fixed to first fixed mold support plate 3 by gear shaft fixing plate 7, and can only move, not rotate. When mold opens along parting surface III, gear shaft 5 moves together with second fixed mold plate 2 and first fixed mold support plate 3. At this point, plastic part 11 is fixed in cavity and cannot move. Movement force of mold opening forces internal thread of plastic part to rotate in helical direction. Therefore, round nut 6 rotates under support of bearing, driving gear 8 fixed on it to rotate, which in turn transmits motion to gear 9, driving internal thread core 10 to rotate, thus achieving automatic demolding of internal thread core.
Figure 9 shows internal thread core assembly, which consists of a fixed mold core insert 11, an internal thread core 12, plastic part 10, sliding bearings 5 and 9, rolling bearings 6 and 8, a gear 7, a set screw 4, a screw 3, an internal thread core end cap 2, and a spring 1. Internal thread core end cap 2, through screw 3, presses set screw 4 and spring 1 to end of internal thread core 12, improving fitting accuracy between set screw 4 and internal thread core 12, and achieving precise axial positioning.
Fig. 9 Internal thread core assembly
1—Spring; 2—Internal thread core end cover; 3—Screw; 4—Set screw; 5, 9—Sliding bearing; 6, 8—Rolling bearing; 7—Gear; 10—Plastic part; 11—Fixed mold core insert; 12—Internal thread core
During mold opening, vibration generated by movement of mold plate may affect contact between fixed mold core insert and internal thread core. Therefore, an axial clamping assembly is added to end of internal thread core. Elasticity of spring 1 keeps both in constant contact with end face of plastic part, preventing scratches or damage to plastic part surface. Properly setting spring tension ensures a smooth and efficient molding and demolding process. During injection molding, injection molding machine locks all mold plates, and fixed mold core insert 11 is tightly connected to internal thread core 12, in close contact with plastic part and other molded parts, ensuring molding quality. To ensure smooth and efficient demolding of internal thread, plastic part and other parts except internal thread core-pulling mechanism need to be separated before demolding to reduce demolding resistance, reduce mold opening force. For this reason, two parting surfaces need to be added to mold, which are used to separate moving mold part, part of fixed mold structure and hot runner part respectively.
1—Spring; 2—Internal thread core end cover; 3—Screw; 4—Set screw; 5, 9—Sliding bearing; 6, 8—Rolling bearing; 7—Gear; 10—Plastic part; 11—Fixed mold core insert; 12—Internal thread core
During mold opening, vibration generated by movement of mold plate may affect contact between fixed mold core insert and internal thread core. Therefore, an axial clamping assembly is added to end of internal thread core. Elasticity of spring 1 keeps both in constant contact with end face of plastic part, preventing scratches or damage to plastic part surface. Properly setting spring tension ensures a smooth and efficient molding and demolding process. During injection molding, injection molding machine locks all mold plates, and fixed mold core insert 11 is tightly connected to internal thread core 12, in close contact with plastic part and other molded parts, ensuring molding quality. To ensure smooth and efficient demolding of internal thread, plastic part and other parts except internal thread core-pulling mechanism need to be separated before demolding to reduce demolding resistance, reduce mold opening force. For this reason, two parting surfaces need to be added to mold, which are used to separate moving mold part, part of fixed mold structure and hot runner part respectively.
3 Mold structure and working process
3.1 Mold structure
Figure 10 is mold assembly drawing. The overall external dimensions of mold are 600 mm * 524 mm * 453 mm. This mold is a non-standard hot runner mold with eight cavities. It adopts a "two-point eight-cavity" hot runner combined with a cold runner gating system with a submarine gate. Plastic part is pushed out by push plate and there is no ejector pin structure. Mold consists of nine templates, which are divided into two main parts: fixed mold and moving mold. Main parting surface III is between moving and fixed molds. Moving mold part includes templates 1, 3 and 4, the rest are fixed mold parts. Internal thread demolding mechanism is mainly concentrated on second fixed mold plate 7, fixed mold support plates 8 and 9. To ensure automatic ejection of internal threaded core and smooth ejection of plastic part, four sets of fixed-distance parting mechanisms are installed in mold, each controlling sequential opening of one of four parting surfaces.
Fig. 10 Mold assembly drawing
1—Moving mold clamping plate; 2—Upper guide pillar; 3—Moving mold support plate; 4—Moving mold plate; 5—First fixed mold plate; 6—Upper guide bushing; 7—Second fixed mold plate; 8—First fixed mold support plate; 9—Second fixed mold support plate; 10—Hot runner fixed plate; 11—Fixed mold clamping plate; 12—Valve pin; 13—Cylinder cover; 14—Hot runner plate; 15—Locating ring; 16—Sprue bushing; 17, 22, 34, 35, 52, 55, 60, 63—Screw; 18—Insulation spacer; 19—Hot runner insert; 20—Nozzle; 21—Nozzle sleeve; 23—Limit bolt; 24—Connection box; 25—Inner runner insert; 26—Outer runner insert; 27—Srue puller insert; 28—Srue puller insert retaining plate; 29—Srue puller; 30—Ejector pillar; 36—Fixed mold insert; 37—Internal thread core; 38—Gear; 39—Fixed mold core insert; 40, 62—Spring; 41—Internal thread core end cover; 42—Locking block; 43—Set screw; 44, 57—Bearing; 45, 46, 58—Limit screw; 47—First core insert; 48—Second core insert; 49—Runner cold slug; 50—Plastic part; 51—Water baffle; 53—Gear shaft clamp plate; 54—Gear shaft end cover; 56—Round nut; 59—Gear shaft; 61—Moving mold insert; 64—Precision positioning pin assembly
1—Moving mold clamping plate; 2—Upper guide pillar; 3—Moving mold support plate; 4—Moving mold plate; 5—First fixed mold plate; 6—Upper guide bushing; 7—Second fixed mold plate; 8—First fixed mold support plate; 9—Second fixed mold support plate; 10—Hot runner fixed plate; 11—Fixed mold clamping plate; 12—Valve pin; 13—Cylinder cover; 14—Hot runner plate; 15—Locating ring; 16—Sprue bushing; 17, 22, 34, 35, 52, 55, 60, 63—Screw; 18—Insulation spacer; 19—Hot runner insert; 20—Nozzle; 21—Nozzle sleeve; 23—Limit bolt; 24—Connection box; 25—Inner runner insert; 26—Outer runner insert; 27—Srue puller insert; 28—Srue puller insert retaining plate; 29—Srue puller; 30—Ejector pillar; 36—Fixed mold insert; 37—Internal thread core; 38—Gear; 39—Fixed mold core insert; 40, 62—Spring; 41—Internal thread core end cover; 42—Locking block; 43—Set screw; 44, 57—Bearing; 45, 46, 58—Limit screw; 47—First core insert; 48—Second core insert; 49—Runner cold slug; 50—Plastic part; 51—Water baffle; 53—Gear shaft clamp plate; 54—Gear shaft end cover; 56—Round nut; 59—Gear shaft; 61—Moving mold insert; 64—Precision positioning pin assembly
3.2 Mold Working Process
(1) Open parting surfaces I and II to separate moving mold part, part of fixed mold structure, and hot runner part. After injection molding, injection molding machine drives moving mold part to move backward. Under action of springs 40 and 62, mold first separates at parting surfaces I and II. Mold opening distance is controlled by spacer screws 58 and 45, which are 30 mm and 40 mm respectively.
When parting surface I opens, moving mold base plate 1, moving mold support plate 3, moving mold plate 4, first core insert 47 and second core insert 48 move backward together, separating moving mold part from plastic part. Simultaneously, parting surface II opens, separating fixed mold structure and hot runner system components, including fixed mold base plate 11, hot runner plate 14, spring 40, internal thread core end cap 41, nozzle 20, valve needle 12, and cylinder head 13, from plastic part. This separation reduces clamping force and axial pressure on plastic part, preparing for automatic release of internal thread core 37.
(2) Parting surface III opens, automatically unscrewing internal thread core. When spacer screw 45 reaches its limit position, spacer lever 23 also reaches its limit. Two sets of spacer levers pull mold plate 7 and mold plate 5 respectively, opening main parting surface III. At this time, linear movement of mold plate drives gear shaft 59 to move, forcing round nut 56 to rotate and driving gear 38 to rotate, thereby driving internal thread core 37 and fixed mold core insert 39 to rotate. Since plastic part remains stationary, internal thread core 37 and fixed mold core insert 39 rotate out of plastic part. Mold opening distance at this stage is controlled by spacer screw 46, is 35mm.
(3) Open parting surface IV, cut off submarine gate and pull out sprue sprue. When spacer screw 46 moves to its limit position, tapered precision positioning pin assembly 64 opens, and parting surface IV opens. Under action of eight pull rods 29, submarine gate is broken off, sprue sprue sprue 49 is pulled out. Injection molding machine stops at limit position, waiting for ejection.
(4) Eject plastic part. During ejection, injection molding machine push rod pushes mold plate 4 through ejector pin 30, causing moving mold insert 61 to move upward. Plastic part is ejected and automatically falls down.
(5) Mold closing. Injection molding machine push rod retracts, moving mold section advances, each mold plate and related component resets in sequence, and each parting surface closes in sequence, completing mold closing process.
When parting surface I opens, moving mold base plate 1, moving mold support plate 3, moving mold plate 4, first core insert 47 and second core insert 48 move backward together, separating moving mold part from plastic part. Simultaneously, parting surface II opens, separating fixed mold structure and hot runner system components, including fixed mold base plate 11, hot runner plate 14, spring 40, internal thread core end cap 41, nozzle 20, valve needle 12, and cylinder head 13, from plastic part. This separation reduces clamping force and axial pressure on plastic part, preparing for automatic release of internal thread core 37.
(2) Parting surface III opens, automatically unscrewing internal thread core. When spacer screw 45 reaches its limit position, spacer lever 23 also reaches its limit. Two sets of spacer levers pull mold plate 7 and mold plate 5 respectively, opening main parting surface III. At this time, linear movement of mold plate drives gear shaft 59 to move, forcing round nut 56 to rotate and driving gear 38 to rotate, thereby driving internal thread core 37 and fixed mold core insert 39 to rotate. Since plastic part remains stationary, internal thread core 37 and fixed mold core insert 39 rotate out of plastic part. Mold opening distance at this stage is controlled by spacer screw 46, is 35mm.
(3) Open parting surface IV, cut off submarine gate and pull out sprue sprue. When spacer screw 46 moves to its limit position, tapered precision positioning pin assembly 64 opens, and parting surface IV opens. Under action of eight pull rods 29, submarine gate is broken off, sprue sprue sprue 49 is pulled out. Injection molding machine stops at limit position, waiting for ejection.
(4) Eject plastic part. During ejection, injection molding machine push rod pushes mold plate 4 through ejector pin 30, causing moving mold insert 61 to move upward. Plastic part is ejected and automatically falls down.
(5) Mold closing. Injection molding machine push rod retracts, moving mold section advances, each mold plate and related component resets in sequence, and each parting surface closes in sequence, completing mold closing process.
4 Trial Molding and Production
Based on three-dimensional drawing and two-dimensional assembly drawing of liquid collector product mold designed above, research group organized personnel to break down assembly drawing, draw drawings of non-standard parts that need to be customized, formulate processing technology for these parts. Subsequently, standard parts such as mold bases were ordered and relevant manufacturers were contacted to process above non-standard parts. During processing, a variety of processing methods such as ordinary machining, CNC machining, wire cutting machining, and EDM were comprehensively adopted. Finally, mold was assembled and trial molding and production were carried out using Haitian MA1200Ⅲ injection molding machine. Fig. 11 shows injection molding machine used for trial molding and production, and Fig. 12 shows liquid collector product produced by injection molding. After testing, quality of plastic product fully meets requirements of enterprise.
Fig. 11 Haitian injection molding machine
Fig. 12 Injection-molded liquid collector product
5 Conclusion
(1) Relevant research results of internal thread rotation demolding were reviewed. Structural characteristics and applications of four commonly used power sources for rotary demolding were compared, providing a theoretical basis for subsequent design of hot runner injection molds for liquid collectors.
(2) A hot runner injection mold for liquid collectors with automatic unscrewing driven by a template was designed. This mold is a non-standard hot runner mold with eight cavities. It uses a template-driven internal thread core-pulling mechanism, employing a hot runner system with a submerged gate combined with a cold runner gating system, and ejects plastic part via a push plate. Production practice shows that mold has a compact structure, reliable operation, and stable product quality.
(3) Structure of internal thread core assembly and fixed mold core insert was innovatively designed. Exhaust devices were installed on the surfaces of both parts to eliminate influence of negative pressure on molding quality of plastic part's end. An axial precision positioning and clamping assembly was installed at the end of internal thread core to ensure stable and efficient molding, parting, internal thread demolding processes. Four sets of fixed-distance parting mechanisms were set up to effectively control four parting sequences of mold. Before demolding internal thread core, irrelevant parts were gradually separated to reduce demolding resistance of plastic part and improve demolding quality.
(4) Feasibility of gating system was verified. A hybrid gating system combining a "two-point, eight-cavity" hot runner and a cold runner was set up, and its feasibility was verified by CAE analysis. Use of hybrid gating system not only fully ensured molding quality of transparent PC plastic parts, but also took advantage of easy-to-cut feature of submarine cold gate, thus improving injection molding production efficiency.
(2) A hot runner injection mold for liquid collectors with automatic unscrewing driven by a template was designed. This mold is a non-standard hot runner mold with eight cavities. It uses a template-driven internal thread core-pulling mechanism, employing a hot runner system with a submerged gate combined with a cold runner gating system, and ejects plastic part via a push plate. Production practice shows that mold has a compact structure, reliable operation, and stable product quality.
(3) Structure of internal thread core assembly and fixed mold core insert was innovatively designed. Exhaust devices were installed on the surfaces of both parts to eliminate influence of negative pressure on molding quality of plastic part's end. An axial precision positioning and clamping assembly was installed at the end of internal thread core to ensure stable and efficient molding, parting, internal thread demolding processes. Four sets of fixed-distance parting mechanisms were set up to effectively control four parting sequences of mold. Before demolding internal thread core, irrelevant parts were gradually separated to reduce demolding resistance of plastic part and improve demolding quality.
(4) Feasibility of gating system was verified. A hybrid gating system combining a "two-point, eight-cavity" hot runner and a cold runner was set up, and its feasibility was verified by CAE analysis. Use of hybrid gating system not only fully ensured molding quality of transparent PC plastic parts, but also took advantage of easy-to-cut feature of submarine cold gate, thus improving injection molding production efficiency.









