If mold parting is not done properly, will the resulting mold be usable?
Time:2026-11-14 08:58:39 / Popularity: / Source:
Injection Mold Parting Surface System Design Specifications (with Design Checklist)
Iron Rule of Parting Surface Design: Parting surface is "lifeline" of mold. Design errors will lead to flash, mold sticking, and a dramatic reduction in mold life!
I. Core Definition and Classification System of Parting Surfaces
Iron Rule of Parting Surface Design: Parting surface is "lifeline" of mold. Design errors will lead to flash, mold sticking, and a dramatic reduction in mold life!
I. Core Definition and Classification System of Parting Surfaces
II. Six Golden Steps to Parting Surface Design
Step 1: Pre-inspection of Product Wall Thickness
Step 1: Pre-inspection of Product Wall Thickness
| Inspection Items | Standard Requirements | Solutions for Exceeding Standards |
| Wall Thickness Uniformity | Δt ≤ 0.2t (t is average wall thickness) | Modify glue position or add a gradual transition |
| Bone Thickness | ≥ 0.4t | Add 0.3-0.5mm R shrinkage reduction at root |
| Crater Structure | Depth = 1.2 x Column Diameter | Additional thickness required if not specified |
Step 2: Draft Angle Strategy Matrix
| Surface Type | Front Mold Draft Angle | Back Mold Draft Angle | Special Requirements |
| Smooth Surface | ≥0.5° | ≥0.3° | Textured Surface: Add 1° |
| Textured Surface | ≥VDI Level 27 + 1° | ≥VDI Level 27 + 0.5° | Deep Cavity: Add 0.5° |
| Assembly Surface | According to Drawing ±0.1° | According to Drawing ±0.1° | Requires 3D Inspection |
Step 3: Thin Steel Risk Control
Minimum Steel Thickness Formula:
H_min = 0.05L + 0.8 (mm)
L: Cantilever Length (mm)
Processing Flow: Identify Cantilever Structure (Aspect Ratio > 3:1); Calculate Theoretical Minimum Steel Thickness; If Actual Value < H_min: Change to Insert Structure; Or Add Support Pillars.
Step 4: Precision Parting Surface Planning
■ Sealing Design: Main sealing surface width ≥ 15mm; Insertion angle ≥ 3° (≥ 5° for precision parts); Contact rate ≥ 85% when parting curved surfaces
■ Venting system: Venting groove depth 0.02-0.03mm; 1cm vent per 100cm² of parting surface
Step 5: Hole and shaft structure processing
Minimum Steel Thickness Formula:
H_min = 0.05L + 0.8 (mm)
L: Cantilever Length (mm)
Processing Flow: Identify Cantilever Structure (Aspect Ratio > 3:1); Calculate Theoretical Minimum Steel Thickness; If Actual Value < H_min: Change to Insert Structure; Or Add Support Pillars.
Step 4: Precision Parting Surface Planning
■ Sealing Design: Main sealing surface width ≥ 15mm; Insertion angle ≥ 3° (≥ 5° for precision parts); Contact rate ≥ 85% when parting curved surfaces
■ Venting system: Venting groove depth 0.02-0.03mm; 1cm vent per 100cm² of parting surface
Step 5: Hole and shaft structure processing
| Feature type | Parting strategy | Precision control |
| Through hole | Mold collision | Eccentricity ≤ 0.02mm |
| Blind hole | Single-sided molding | Draft angle ≥ 0.5° |
| Rotary axis | Haff slider | Mold line ≤ 0.01mm |
Step 6: Decision Tree for Puncture Direction
III. Fatal Pitfalls in Parting Surface Design
| Pitfalls | Consequences | Preventative Measures |
| Sharp Angle Penetration (<3°) | Stretch/Scorch | Additional Wear Plate (DLC Coating) |
| Unpredeformed Surface | Flash ≥ 0.1mm | Thermal Expansion Compensation δ = α·L·ΔT |
| Insufficient Venting | Air Trapped Burning | Vent Pins Every 50mm² on Parting Surface |
| Unbalanced Clamping Force | Form Deformation | Finite Element Analysis Deformation ≤ 0.02mm/100mm |
IV. 3D Pre-Parting Checklist
1. Wall Thickness Analysis Report (Thinnest/Thickest Points Marked)
2. Draft Angle Inspection Diagram (Red Areas Indicate Non-Compliant Areas)
3. Undercut Identification (Automatically Generate Undercut Vector Diagram)
4. Parting Line Feasibility Verification (Automatically Generate Parting Line Diagram)
5. Interference Pre-check (Motion Envelope Collision Test)
V. Parting Surface Design Case Library
1. Wall Thickness Analysis Report (Thinnest/Thickest Points Marked)
2. Draft Angle Inspection Diagram (Red Areas Indicate Non-Compliant Areas)
3. Undercut Identification (Automatically Generate Undercut Vector Diagram)
4. Parting Line Feasibility Verification (Automatically Generate Parting Line Diagram)
5. Interference Pre-check (Motion Envelope Collision Test)
V. Parting Surface Design Case Library
| Product Type | Parting Solution | Key Technical Points |
| Automotive Lampshade | Hyperboloid Parting + Four Sliders | Surface Fitting Accuracy ±0.03mm, Hot Runner Timing Control |
| Medical Syringes | 180° Rotary Parting | Coaxiality ≤ Φ0.01mm, Medical-Grade Polish Ra 0.05μm |
| Electronic Connector | Tunnel Sliders + Lifter Parting | 7° Insertion Angle, Chrome Finish HV1000 |
VI. Parting Surface Design Tips
First, Product Parting, Second, Mold Parting; Third, Inspection, Fourth, Repair
Accurately Measure Wall Thickness Before Demolding, Ensure Sharp Corners Do Not Leak
Observe Appearance in Direction of Penetration, Calculate Surface Expansion
No Need to Handle Without 3D Inspection, Saving Time, Material, and Worry
Designed according to this specification, mold parting success rate increases by 90%, and number of mold trials is reduced to ≤2 times!
First, Product Parting, Second, Mold Parting; Third, Inspection, Fourth, Repair
Accurately Measure Wall Thickness Before Demolding, Ensure Sharp Corners Do Not Leak
Observe Appearance in Direction of Penetration, Calculate Surface Expansion
No Need to Handle Without 3D Inspection, Saving Time, Material, and Worry
Designed according to this specification, mold parting success rate increases by 90%, and number of mold trials is reduced to ≤2 times!

