Common Plastic Names, Abbreviations, and Injection Molding Temperature Parameters
Time:2026-11-10 08:11:49 / Popularity: / Source:
During injection molding, various problems can arise, such as deformation, cracking, crazing, weld lines, and smears. These are all more or less related to injection temperature. Accuracy of temperature setting greatly affects product's appearance and performance. When setting injection temperature, temperature at feed inlet should not be too high to prevent blockages and escape of trapped air. Before injection molding, let's learn about "common plastic injection temperature parameters."
Summary of Common Plastic Injection Molding Temperature Parameters
Summary of Common Plastic Injection Molding Temperature Parameters
Several common issues deserve attention in injection molding production
Because transparent plastics require high light transmittance, surface quality of plastic products must be strictly controlled. Defects such as spots, pores, whitening, spraying, black spots, color difference, and poor color are unacceptable. Therefore, throughout injection molding process, strict, even special, requirements must be placed on design of raw materials, equipment, molds, and even product itself. Secondly, because transparent plastics are mostly high-melting-point and have poor fluidity, to ensure product surface quality, it is often necessary to fine-tune process parameters such as barrel temperature, injection pressure, and injection speed. This ensures that mold is filled completely during injection without generating internal stress, which could lead to product deformation and cracking.
Following is about material preparation. We will discuss issues that should be noted from several aspects, including equipment and mold requirements, injection molding process, raw material handling.
1. Raw Material Preparation and Drying: Even the slightest impurity in plastic will affect product's transparency, thus impacting storage and transportation. Proper sealing is crucial during feeding to ensure raw materials are clean and hygienic. Especially important is drying process, as moisture in raw materials can cause deterioration upon heating. Therefore, drying is essential, a drying hopper must be used when adding raw materials during injection molding. Furthermore, incoming air during drying process should ideally be filtered and dehumidified to prevent contamination of raw materials.
2. Cleaning of Barrel, Screw, and Accessories.
Following is about material preparation. We will discuss issues that should be noted from several aspects, including equipment and mold requirements, injection molding process, raw material handling.
1. Raw Material Preparation and Drying: Even the slightest impurity in plastic will affect product's transparency, thus impacting storage and transportation. Proper sealing is crucial during feeding to ensure raw materials are clean and hygienic. Especially important is drying process, as moisture in raw materials can cause deterioration upon heating. Therefore, drying is essential, a drying hopper must be used when adding raw materials during injection molding. Furthermore, incoming air during drying process should ideally be filtered and dehumidified to prevent contamination of raw materials.
2. Cleaning of Barrel, Screw, and Accessories.
To prevent raw material contamination and accumulation of old material or impurities in screw and accessory recesses, especially with resins with poor thermal stability, screw cleaners should be used to clean all parts before use and after shutdown. If screw cleaner is unavailable, PE or PS resins can be used to clean screw. During temporary shutdowns, to prevent prolonged exposure to high temperatures and potential degradation of materials, temperature of dryer and barrel should be lowered to below 160℃, for materials such as PC and PMMA. (For PC, hopper temperature should be reduced to below 100℃)
3. Issues to Consider in Mold Design (Including Product Design). To prevent problems such as poor backflow and uneven cooling during plastic molding, which can lead to surface defects and deterioration, following points should generally be considered in mold design:
① Wall thickness should be as uniform as possible, and draft angle should be sufficiently large; ② Transition period should be gradual, avoiding sharp corners and rounded transitions. For PC products, no notches should be allowed; ③ Gates. Flow channels should be as wide and short as possible, gates should be designed according to shrinkage and solidification process. Cold slug wells should be added if necessary; ④ Mold surface should be flat and have low roughness (preferably less than 0.8); ⑤ Venting slots must be large enough to allow for timely discharge of gas and melt; ⑥ Except for PET, wall thickness should not be too thin, generally not less than 1 mm.
4. Issues to be aware of regarding injection molding process (including requirements for injection molding machine): To reduce internal stress and surface quality defects, following points should be noted during injection molding:
① Select a dedicated screw injection molding machine with a nozzle having separate temperature control; ② Injection temperature: A higher injection temperature is preferable without decomposing plastic resin; ③ Injection pressure: Generally higher, overcoming disadvantage of high melt viscosity, but excessive pressure can generate internal stress, causing difficulty in demolding and deformation; ④ Injection speed: Generally lower while meeting mold filling requirements, preferably using a slow-fast-slow multi-stage injection process; ⑤ Holding time and molding cycle: Should be shortened as much as possible while meeting product mold filling requirements, preventing sink marks and bubbles, to minimize material's residence time in barrel; ⑥ Screw speed and back pressure: Should be reduced as much as possible while meeting plasticizing quality requirements to prevent potential degradation; ⑦ Mold temperature: Cooling performance of product greatly affects quality; therefore, mold temperature must be precisely controlled, and a higher mold temperature is preferable if possible.
5. Other Matters. To prevent surface quality deterioration, mold release agents should be used sparingly during general injection molding, amount reused should not exceed 20%. All products except PET should undergo post-treatment to eliminate internal stress. PMMA should be circulated and dried in hot air at 70-80℃ for 4 hours, while PC should be dried in clean air, glycerin, or liquid wax at 110-135℃ for a period varying depending on product, but not exceeding 10 hours. Furthermore, PET requires biaxial stretching to achieve good mechanical properties.
Transparency of Plastics: Transparency must be guaranteed first, followed by sufficient strength and abrasion resistance. It should also be impact-resistant, heat-resistant, chemically resistant, and have good water absorption. Only in this way can transparency requirements be met during use, and product's lifespan extended.
Compared to PC, PC offers a more desirable alternative, but its main raw materials are expensive and injection molding is difficult. Therefore, PMMA remains primary choice (for products with general requirements). PPT, on the other hand, requires stretching to achieve good mechanical properties and is mostly used in packaging and containers.
Injection Molding Technology for Transparent Plastics: Processing Properties: In addition to common issues mentioned above, transparent plastics each possess certain processing properties, which are described below:
1. Processing Characteristics of PMMA: PMMA has high viscosity and poor flowability, requiring high material temperature and high injection pressure for production. Injection temperature has a greater impact than injection pressure, but increasing injection pressure helps improve shrinkage rate of product. It has a wide injection temperature range, with a melting temperature around 160℃ and a decomposition temperature around 270℃. Therefore, material temperature can be adjusted widely, resulting in good processability. Improving flowability can begin with increasing injection temperature. It has poor impact resistance and wear resistance, making it prone to scratches and cracking. Therefore, increasing mold temperature and improving solidification process are necessary to overcome these drawbacks.
2. PC has high viscosity and a high melt temperature, resulting in poor fluidity. Therefore, it must be injected at a high temperature (270-320℃). Compared to PMMA, its temperature adjustment range is narrower, and its processability is not as good. Injection pressure has little effect on fluidity, but due to its high viscosity, a relatively high injection pressure is still required. To prevent internal stress, holding time should be minimized. It has high shrinkage and dimensional stability, but finished product has high internal stress and is prone to cracking. Therefore, it is best to improve fluidity by increasing temperature rather than pressure, reduce possibility of cracking by increasing mold temperature, improving mold structure, and post-processing. When injection speed is low and defects such as ripples are prone to occur at gate, nozzle temperature should be controlled separately, mold temperature should be increased, runner and gate resistance should be reduced.
3. PET has a high molding temperature and a narrow temperature adjustment range (260-300℃). However, after melting, due to its good fluidity, its processability is poor, and anti-spillage devices are often required on nozzle. Its mechanical strength and post-injection properties are not high, performance must be improved through stretching processes and modification. Precisely control mold temperature to prevent deformation. A crucial factor affecting deformation, hot runner dies are recommended. High mold temperature is essential; otherwise, poor surface gloss and difficulty in demolding will occur.
Transparency Defects and Solutions: Due to space limitations, this section only discusses defects affecting product transparency, which may include:
1. Silver streaks: During filling and solidification, anisotropy of internal stress causes stress in vertical direction, leading to resin flow orientation. This creates streaks with different refractive indices compared to non-flow orientations. When these streaks expand, they may cause product cracking.
2. Air bubbles: Water vapor and other gases in resin cannot escape (during mold solidification) or due to insufficient filling, resulting in excessively rapid surface solidification and formation of "vacuum bubbles."
3. Poor surface gloss: This is mainly manifested by high mold surface roughness and premature solidification, preventing resin from replicating mold surface's condition. All of this results in fine unevenness on mold surface, causing product to lose its gloss.
4. Whitening and Smoke/Dust: Primarily caused by airborne dust settling on raw material or excessively high moisture content in raw material.
5. White Smoke and Black Spots: Mainly caused by localized overheating inside mold barrel, leading to resin decomposition or deterioration.
6. Vibration Marks: Due to excessively high melt viscosity, material at front solidifies within mold cavity, and subsequent material breaks through solidification surface, causing vibration marks on the surface, appearing as dense ripples originating from center of sprue.
3. Issues to Consider in Mold Design (Including Product Design). To prevent problems such as poor backflow and uneven cooling during plastic molding, which can lead to surface defects and deterioration, following points should generally be considered in mold design:
① Wall thickness should be as uniform as possible, and draft angle should be sufficiently large; ② Transition period should be gradual, avoiding sharp corners and rounded transitions. For PC products, no notches should be allowed; ③ Gates. Flow channels should be as wide and short as possible, gates should be designed according to shrinkage and solidification process. Cold slug wells should be added if necessary; ④ Mold surface should be flat and have low roughness (preferably less than 0.8); ⑤ Venting slots must be large enough to allow for timely discharge of gas and melt; ⑥ Except for PET, wall thickness should not be too thin, generally not less than 1 mm.
4. Issues to be aware of regarding injection molding process (including requirements for injection molding machine): To reduce internal stress and surface quality defects, following points should be noted during injection molding:
① Select a dedicated screw injection molding machine with a nozzle having separate temperature control; ② Injection temperature: A higher injection temperature is preferable without decomposing plastic resin; ③ Injection pressure: Generally higher, overcoming disadvantage of high melt viscosity, but excessive pressure can generate internal stress, causing difficulty in demolding and deformation; ④ Injection speed: Generally lower while meeting mold filling requirements, preferably using a slow-fast-slow multi-stage injection process; ⑤ Holding time and molding cycle: Should be shortened as much as possible while meeting product mold filling requirements, preventing sink marks and bubbles, to minimize material's residence time in barrel; ⑥ Screw speed and back pressure: Should be reduced as much as possible while meeting plasticizing quality requirements to prevent potential degradation; ⑦ Mold temperature: Cooling performance of product greatly affects quality; therefore, mold temperature must be precisely controlled, and a higher mold temperature is preferable if possible.
5. Other Matters. To prevent surface quality deterioration, mold release agents should be used sparingly during general injection molding, amount reused should not exceed 20%. All products except PET should undergo post-treatment to eliminate internal stress. PMMA should be circulated and dried in hot air at 70-80℃ for 4 hours, while PC should be dried in clean air, glycerin, or liquid wax at 110-135℃ for a period varying depending on product, but not exceeding 10 hours. Furthermore, PET requires biaxial stretching to achieve good mechanical properties.
Transparency of Plastics: Transparency must be guaranteed first, followed by sufficient strength and abrasion resistance. It should also be impact-resistant, heat-resistant, chemically resistant, and have good water absorption. Only in this way can transparency requirements be met during use, and product's lifespan extended.
Compared to PC, PC offers a more desirable alternative, but its main raw materials are expensive and injection molding is difficult. Therefore, PMMA remains primary choice (for products with general requirements). PPT, on the other hand, requires stretching to achieve good mechanical properties and is mostly used in packaging and containers.
Injection Molding Technology for Transparent Plastics: Processing Properties: In addition to common issues mentioned above, transparent plastics each possess certain processing properties, which are described below:
1. Processing Characteristics of PMMA: PMMA has high viscosity and poor flowability, requiring high material temperature and high injection pressure for production. Injection temperature has a greater impact than injection pressure, but increasing injection pressure helps improve shrinkage rate of product. It has a wide injection temperature range, with a melting temperature around 160℃ and a decomposition temperature around 270℃. Therefore, material temperature can be adjusted widely, resulting in good processability. Improving flowability can begin with increasing injection temperature. It has poor impact resistance and wear resistance, making it prone to scratches and cracking. Therefore, increasing mold temperature and improving solidification process are necessary to overcome these drawbacks.
2. PC has high viscosity and a high melt temperature, resulting in poor fluidity. Therefore, it must be injected at a high temperature (270-320℃). Compared to PMMA, its temperature adjustment range is narrower, and its processability is not as good. Injection pressure has little effect on fluidity, but due to its high viscosity, a relatively high injection pressure is still required. To prevent internal stress, holding time should be minimized. It has high shrinkage and dimensional stability, but finished product has high internal stress and is prone to cracking. Therefore, it is best to improve fluidity by increasing temperature rather than pressure, reduce possibility of cracking by increasing mold temperature, improving mold structure, and post-processing. When injection speed is low and defects such as ripples are prone to occur at gate, nozzle temperature should be controlled separately, mold temperature should be increased, runner and gate resistance should be reduced.
3. PET has a high molding temperature and a narrow temperature adjustment range (260-300℃). However, after melting, due to its good fluidity, its processability is poor, and anti-spillage devices are often required on nozzle. Its mechanical strength and post-injection properties are not high, performance must be improved through stretching processes and modification. Precisely control mold temperature to prevent deformation. A crucial factor affecting deformation, hot runner dies are recommended. High mold temperature is essential; otherwise, poor surface gloss and difficulty in demolding will occur.
Transparency Defects and Solutions: Due to space limitations, this section only discusses defects affecting product transparency, which may include:
1. Silver streaks: During filling and solidification, anisotropy of internal stress causes stress in vertical direction, leading to resin flow orientation. This creates streaks with different refractive indices compared to non-flow orientations. When these streaks expand, they may cause product cracking.
2. Air bubbles: Water vapor and other gases in resin cannot escape (during mold solidification) or due to insufficient filling, resulting in excessively rapid surface solidification and formation of "vacuum bubbles."
3. Poor surface gloss: This is mainly manifested by high mold surface roughness and premature solidification, preventing resin from replicating mold surface's condition. All of this results in fine unevenness on mold surface, causing product to lose its gloss.
4. Whitening and Smoke/Dust: Primarily caused by airborne dust settling on raw material or excessively high moisture content in raw material.
5. White Smoke and Black Spots: Mainly caused by localized overheating inside mold barrel, leading to resin decomposition or deterioration.
6. Vibration Marks: Due to excessively high melt viscosity, material at front solidifies within mold cavity, and subsequent material breaks through solidification surface, causing vibration marks on the surface, appearing as dense ripples originating from center of sprue.




