Various Lifter Structures

Time:2026-11-19 09:53:11 / Popularity: / Source:

1. Conventional Design

There are many types of lifter structures, a wide variety. Besides those shown in Figure 9-82, common lifter structures include T-slot structure and pin structure shown in Figure 9-83. Many other structures are variations of these basic structures, mainly reflected in sliding method of slider seat. In Figure 9-83(a), width of one side of T-slot should be >2mm; too wide will affect strength of lifter. Smaller lifters can also use only a single-sided T-slot. In Figure 9-83(b), pin needs to be hardened, with a diameter ≥4mm and a dimension T ≥4mm.
Lifter Structure 
Figure 9-83 Conventional design of lifter

2. Simple Lifter

There are many simple lifter structures; several common ones are shown in Figure 9-84. In export molds, conventional lifter designs should connect lifter to push plate. Simplified lifters can only be used in special cases such as excessively long lifters, limited space, exceeding ejector plate range, and mutual interference. In molds exported to Europe, America, and Japan, use of simplified lifters should be confirmed by customer.
Lifter Structure 
Figure 9-84 Simplified Lifter Structure
Note that simplified lifters should not be used in molds with fixed-mold angled spring slides, as this may cause interference between spring slide and ejector, preventing ejector from resetting.

3. Minimal Lifter Design

Minimum lifters are used when plastic part is small. Due to structural limitations of plastic part, size and stroke of lifter are very small. In this case, strength of lifter is very weak. Therefore, length of lifter should be shortened as much as possible, a reliable lifter guiding mechanism should be used, and lifter parts should be nitrided. Figure 9-85 shows structure of a minimal lifter for a mobile phone casing. Height of lifter seat 5 is increased, allowing it to slide within guide block 4, and length of lifter 2 is shortened. Lifter 2 and lifter seat 5 are fitted with an arc surface.
Lifter Structure 
Figure 9-85 Structure of a Minimal Lifter (Part 1)
1 - Core; 2 - Lifter; 3 - Moving Mold Platen; 4 - Lifter Guide Block; 5 - Lifter Seat; 6 - Push Rod Fixing Plate; 7 - Push Plate; 8 - Screw; 9 - Spring Washer; 10 - Moving Mold Base Plate
Figure 9-86 shows another design method for minimal Lifters. When cross-sectional dimensions of ejector pin are very small, such as 4mm x 5mm or 6mm x 6mm, it cannot be extended to ejector pin fixing plate. In this case, ejector pin 5 is connected using a single-sided T-slot. Ejector pin material is 1.2343, heat-treated to 54HRC. Ejector pin 5 slides within guide tube 6, and head of guide tube is fixed to back of plate B with a pressure block. Ejector pin 5 is prevented from rotating using anti-rotation washers 10.
Lifter Structure 
Figure 9-86 Structure of a Minimal Lifter (II)
1 - Cavity; 2 - Core; 3 - Moving Mold Insert; 4 - Lifter; 5 - Ejector Rod; 6 - Guide Tube; 7 - B Plate; 8 - Pressure Block; 9 - Screw; 10 - Anti-rotation Washer; 11 - Ejector Rod Fixing Plate; 12 - Ejector Plate; 13 - Moving Mold Base Plate

4. Large Ejector Pin

Design of a large ejector pin is shown in Figures 9-87 and 9-88. When ejector pin is very large, if it is directly extended and connected to ejector plate, clearance hole in plate B will be very large, leading to a weakening of plate B's strength. This will also weaken strength of ejector pin fixing plate after machining, causing ejector plate to bear injection pressure and resulting in ejection system failure. Furthermore, it wastes mold steel.
Lifter Structure 
Figure 9-87 Split-type lifter
1. Fixed mold base plate; 2. Split-type lifter; 3. Locating pin; 4. Core; 5. Moving mold insert; 6. Guide rod; 7. Bronze guide sleeve; 8. Moving mold plate; 9. Elastic retaining ring for hole; 10. Sliding block; 11, 16. Screws; 12. Push rod fixing plate; 13. Push plate; 14. Moving mold base plate; 15. Pressure plate; 17. lifter seat
Lifter Structure 
Figure 9-88 T-shaped Lifter
1 Fixed mold base plate; 2 Lifter; 3 Core; 4 Moving mold plate; 5 Limiting block; 6 T-shaped push rod; 7 Push rod fixing plate; 8 Positioning pin; 9 Push plate; 10 Moving mold base plate
When designing a large ejector pin, it is necessary to pay attention to designing a corresponding cooling circuit.
Figure 9-89 shows an application example of a T-slot ejector pin. Figure (a) shows wire channel of a large CT scanner body. Product's dimensions are 434.3mm x 128.56mm x 23.50mm. Plastic part is relatively long with narrow grooves on edges. Plastic part exerts a large clamping force on moving mold core. Space within narrow groove is limited, making it impossible to design ejector pins because ejector pins with a diameter of less than 62mm have limited ejection force. If a straight ejector is designed, it will clamp product and make it difficult to demold. Therefore, a lifter must be designed to demold plastic part. Figure (b) shows design of a T-slot lifter. Because plastic part has a curved and irregular shape in horizontal plane, T-slot lifter on each side needs to be divided into two sections. Each lifter needs to be designed with two ejector pins to maintain ejection balance. It is necessary to ensure that lengths of two T-shaped ejector pins 4 are completely consistent.
Lifter Structure 
Lifter Structure 
Figure 9-89 Application Example of T-Slot Lifter
1 - Cavity; 2 - Lifter; 3 - Core; 4 - T-shaped Ejector; 5 - Moving Template; 6 - Ejector Fixing Plate; 7 - Screw; 8 - Ejector Plate; 9 - Moving Mold Base Plate

5. Linkage-type lifter

Figure 9-90 shows an example of circumferential demolding with a linkage-type lifter. Plastic part is a circular product with 6 undercuts on inner circumference, requiring a lifter for demolding. Lifter structure is a linkage-type lifter. After ejection, lifter detaches from moving mold core. Therefore, lifter and moving mold core are guided by a T-slot. Draft angles are designed on all three sides of lifter. Connecting rod 5, lifter 2, and sliding block 8 are all connected by cylindrical pins. Linkage-type lifter features reliable structure and low ejection friction resistance.
Lifter Structure 
Figure 9-90 Linkage-type lifter circumferential demolding
1-Core; 2-Lifter; 3-Rotating pin; 4-B plate; 5-Connecting rod; 6-Push rod fixing plate; 7-Rotating pin; 8-Sliding block; 9-Lifter seat; 10-Push plate; 11-Screw; 12-Moving mold base plate
Figure 9-91 shows a hinged lifter, a structure derived from PCS standard. PCS is a well-known American supplier of standard mold components; therefore, hinged lifters are often used in molds exported to United States. During design, it is important to note that lifter connecting rod 7 cannot be designed vertically; it needs to be inclined at 1°~2° in direction of movement. Arc mating surfaces between lifter 4, connecting rod 7, and lifter seat 9 all require wire cutting. All lifter components require nitriding treatment. Note that ejector plate needs guide pillars for guidance, and return of ejection system must be accurate and timely.
Lifter Structure 
Figure 9-91 Hinge-type Lifter Demolding
1 - Cavity; 2 - Moving Mold Insert; 3 - Core; 4 - Lifter; 5 - B Plate; 6 - Lifter Guide Block; 7 - Lifter Connecting Rod; 8 - Ejector Rod Fixing Plate; 9 - Lifter Seat; 10 - Ejector Plate
  1. 6. Flexible lifter
Flexible lifters originated in Europe and are currently widely used in export molds. Flexible Lifters are characterized by their small footprint and simple structure, and are particularly advantageous when two lifters are tightly fitted together. Flexible Lifter is made of 1.2106 spring steel, with a core hardness of 45 HRC and a working surface hardness of 55 HRC. An application example of a flexible lifter is shown in Figure 9-92. Specifications of DMS flexible lifter are shown in Figure 9-93, application precautions for DMS flexible Lifter are shown in Figure 9-94, design considerations for flexible lifter are shown in Figure 9-95.
Lifter Structure 
Figure 9-92 Application Example of Elastic Lifter
1 Fixed mold plate; 2 Cavity; 3 Core; 4 Moving mold plate; 5 Elastic Lifter; 6 Return Spring; 7 Reset Rod; 8 Push Rod Fixing Plate; 9 Screw; 10 Push Plate; 11 Disc Spring
Lifter Structure 
Figure 9-93 DMS Flexible Lifter Specifications
Lifter Structure 
Figure 9-94 Precautions for application of DMS elastic lifter
Lifter Structure 
Figure 995 Key Design Considerations for Flexible Lifters
In Figure 9-92, when using a flexible lifter, locking position should not be too large, and locking part needs sufficient draft angle 'a'. A disc spring 11 needs to be designed at the bottom of return rod, or a yellow rubber or spring can be used as initial return element.
Design considerations for flexible lifters are as follows:
Inclined surface of elastic ejector (i.e., back of adhesive part) is fully fitted with core (i.e., ensuring fitting length l1 value), as shown by inclined surface indicated by 1 in Figure 9-94(a); If elastic ejector is too long during installation, it can be shortened from bottom thread; Elastic ejector stroke (H value) refers to stroke at the highest point of head after full ejection; stroke decreases accordingly from head downwards. Surface where undercut is located is perpendicular to parting surface, and length of sealing surface is not less than 1/3h, as shown in Figure 9-94(a) 2 (vertical surface); Diameter of moving template mounting hole is d + 0.1 + 0.2, and thickness of push plate fixing plate is not less than 15mm, as shown in Figure 9-94(a) 4 (dimension); Push plate ejection stroke must be less than h, as shown in Figure 9-94(b) 3 (dimension); To ensure smooth demolding, draft angle 'a' of snap-fit should be maximized, with a minimum draft angle of 2, as shown in Figure 9-94(c) 5 (dimension); Length tolerance of elastic angled ejector is nominal dimension + 0.02 to + 0.05, as shown in Figure 9-94(c) 6 (dimension).a

Go To Top