Research on CNC Machining Technology of Large Injection Molding Mold Plates Based on Residual Stress

Time:2026-11-11 08:28:34 / Popularity: / Source:

0 Introduction

Large injection molding mold plate are core load-bearing components of plastic molding equipment. Their flatness, parallelism and hole position accuracy directly determine mold clamping rigidity of injection molding machine and molding quality of product. With increasing demand for integrated molding of large injection-molded parts such as integrated battery casings and smart cockpits for new energy vehicles, mold plate sizes have jumped from 1,000 mm level to over 2,000 mm, with material removal rates exceeding 80%.
Large mold plates, after casting, tempering, and rough machining, already contain significant initial residual stresses due to disruption of initial residual stress equilibrium state of blank (material removal). If these initial residual stresses are not coordinated with additional cutting stresses during machining, their combined effect will cause warping deformation and hole displacement, and in severe cases, the entire mold mold plate may be scrapped. Zhuang Kejia et al. studied evolution of residual stress in titanium alloy cutting using coupled Euler-Lagrange (CEL) method; Xu Feifei et al. and Dong Lizhuo et al. established stress-relief-machining deformation simulation models for 7075 aluminum alloy thin-walled parts and TC11 titanium alloy disc-shaped parts, respectively; Zhao Changlong et al. reduced residual stress by 18.55% in H13 mold steel laser cladding by pre-setting surface texture; Zhao Xikun et al., Gao Yi et al., and Lu Xianglin et al. introduced neural networks and multi-objective optimization algorithms into process parameter design. Han Xiong et al. and Zhang Dingquan et al. conducted systematic research on residual stress analysis in high-speed ultrasonic vibration milling and X-ray diffraction, respectively. Existing work mainly focuses on aerospace thin-walled parts, and there are relatively few reports on systematic research on characteristics of large injection molding mold plate, such as high material removal rate, large initial residual stress, and strict assembly precision.
This paper takes QT600-3 ductile iron mold mold plate as the object, analyzes influence of initial residual stress on machining deformation by combining testing and simulation. A CNN-LSTM prediction model is constructed and combined with NSGA-GWO algorithm to jointly optimize process parameters. Finally, effectiveness of method is verified through actual machining. Aim is to provide a process optimization paradigm integrating "measurement-simulation-control" for precision machining of large injection mold mold plate.

1 Experimental Section (Excerpt)

Initial Residual Stress Testing Method
Initial stress of blank was tested using XRD and blind hole method (BH). As shown in Figure 3, XRD measurement points were arranged along a 9-point grid (300 mm * 300 mm spacing) on upper surface to measure plane stress σx and σy in shallow surface layer (approximately 10 μm). Blind hole method was used with 12 measurement points on the side and bottom surfaces to reflect stress in thickness direction and side surface. Thickness gradient of upper surface was measured layer by layer from 0 to 5 mm by XRD combined with layered electrolytic polishing (each layer is about 50 μm). Distribution of σx and σy was measured layer by layer from 0 to 5 mm by blind hole method. Before testing, surface was cleaned with acetone and oxide layer was lightly ground with 600# sandpaper. XRD was performed using side tilt method with fixed ψ angles of 0°, 15°, 30° and 45°. Average value was taken for each point after 3 measurements. Blind hole method had a hole diameter of 1.5 mm and a hole depth of 2.0 mm. Release coefficients A=-0.078 and B=-0.178 were taken according to ASTM E837-2013. 9 points were numbered P1~P9, 12 points on the side and bottom were numbered S1~S12.
injection-molded parts 
Figure 3 Initial residual stress test point arrangement of mold plate blank
Thermo-mechanical coupling simulation of the whole processing process
Simulation process is divided into 3 steps:
(1) Establish the initial stress field of blank. Based on data in Section 1.3, stress tensor was mapped to nodes as initial conditions using a Python script and written to INP file via `*initial conditions, type=stress`.
(2) Establishing a cutting thermo-mechanical coupling model. ABAQUS/Explicit solver was used, with tool simplified to a rigid body; workpiece was meshed using eight-node hexahedral linear reduced integral elements (C3D8RT), approximately 280,000 elements. Contact surface adopted Coulomb friction model, defining evolution of friction coefficient with temperature and sliding speed through VFRICTION subroutine; cutting heat source consisted of plastic deformation heat and frictional heat generated at tool-chip/tool-workpiece interface; temperature field and stress field were solved bidirectionally. Machining area used a 0.2 mm fine mesh, far area a 1.0 mm coarse mesh, transition ratio was 1.2; mesh independence verification showed that maximum compressive stress amplitude difference between 0.2 mm and 0.15 mm schemes was <2.3%, and deformation difference was <1.8%. Constitutive parameters and friction coefficients are taken from QT600-3 milling literature.
(3) After cutting, tool is removed and constraints are reapplied. Static equilibrium analysis is performed on workpiece to obtain stress field and deformation field. Static analysis uses ABAQUS/Standard solver, with post-machining stress as initial condition to solve equilibrium state. Nodal displacements are machining deformations.
CNN-LSTM Residual Stress Prediction Model
Maximum, minimum, and root mean square values of machined surface stress under different parameter combinations (rotation speed, feed per tooth, radial cutting width, tool diameter, and cutting layer depth) in simulation in Section 1.4 are used as labels to construct a CNN-LSTM prediction model. Model input layer receives 8-dimensional features (5-dimensional parameters + 3-dimensional initial stress: maximum tensile stress, compressive stress amplitude, thickness gradient) to adapt to different blanks. Rationale for choosing a CNN-LSTM combination is as follows: Influence of processing parameters and initial stress on residual stress exhibits significant spatial nonlinear coupling (suitable for extracting local spatial features using CNN convolutional kernels), while stress response of adjacent cutting layers during layered cutting exhibits temporal dependence (suitable for LSTM modeling). Combining the two can simultaneously capture both spatial and temporal features, resulting in superior predictive performance compared to a single CNN or LSTM (see Table 2 for ablation experiment comparison).
A CNN feature extraction module is constructed using a combination of dual convolutional layers and a single pooling layer to uncover nonlinear spatial coupling relationship between model input parameters and initial stress field. An LSTM temporal modeling layer with 64 hidden units is built. Hidden state vector of this layer encodes transmission effect of stress from each layer to subsequent cutting layers within layered cutting depth dimension. 64-dimensional state representation capacity can fully characterize stress accumulation and evolution within a continuous 10-layer range, corresponding to memory depth of stress redistribution effects throughout material removal process at physical level. This captures temporal correlation features of stress between adjacent cutting layers, ultimately outputting three sets of stress feature quantities. Adam optimizer was used for model training, with an initial learning rate of 0.001, batch size of 32, and a total number of iterations of 200. A Dropout coefficient of 0.2 was introduced to alleviate network overfitting. Accuracy was evaluated by R² and RMSE, as shown in equations (1) and (2):
injection-molded parts 
injection-molded parts 
NSGA-GWO Multi-Objective Optimization Method
Multi-objective optimization model was constructed with objective functions of minimizing standard deviation of residual stress δσ and maximum deformation δmax on machined surface, as shown in equation (3):
injection-molded parts 
Where x=[n,fz,ae,D,ap], design variables, consist of five core milling process parameters that can be independently programmed and set in CNC system: spindle speed n, feed per tooth fz, radial cutting width ae, tool diameter D, and cutting depth ap. Their value ranges are shown in Table 3, their sensitivities to residual stress and machining deformation vary.
Parameters Symbol Lower bound Upper bound
Spindle speed/r*min⁻¹ n 2000 6000
Feed per tooth/mm fz 0.08 0.20
Radial width/mm ae 0.2 1.0
Tool diameter/mm D 20 50
Depth of cut/mm ap 0.5 2.0
Table 3 Range of CNC machining process parameters
NSGA-GWO algorithm was used to optimize CNN-LSTM prediction model, with a population size of 50 and a maximum iteration of 200 generations. After termination, TOPSIS method was used to screen comprehensive optimal solution from Pareto front.Variables and their ranges are shown in Table 3. According to literature, NSGA-GWO hybrid strategy takes into account both global search and local development capabilities.
Process flow
Process flow is shown in Figure 4, which mainly includes five stages: blank inspection, initial stress field establishment, parameter optimization, machining execution, deformation detection and feedback: (1) Inspection stage: inspect appearance, hardness, initial stress and register and file; (2) Stress field establishment stage: map test data to finite element model; (3) Parameter optimization stage: optimize based on CNN-LSTM and NSGA-GWO; (4) Machining execution stage: program according to optimization results, use six-point symmetrical clamping and symmetrical tooling for finishing; (5) Deformation detection and feedback stage: use coordinate measuring machine for inspection, and if deviation is out of tolerance, feedback optimization module will perform secondary optimization.
injection-molded parts 
Figure 4. Process flow for controlling residual stress in large injection molding mold plate.
Above five stages constitute a complete closed-loop control system of "detection-optimization-processing-feedback". Each mold plate is customized based on its initial stress state, breaking through limitations of "one-size-fits-all".

2. Results and Discussion

2.1. Initial Residual Stress Distribution of Large Injection Molding mold plate Blanks

Figure 5 shows initial stress test results of QT600-3 blank. As shown in Figure 5(a), σx along x-direction is asymmetrically distributed on upper surface: tensile stress dominates in the middle (+28 MPa), while compressive stress dominates at four corners (-45 MPa). This is due to faster heat dissipation at four corners than in the middle during casting and cooling, resulting in uneven shrinkage and formation of gradient stress areas. As shown in Figure 5(b), distribution of σy along y-direction is similar to σx, but amplitude is slightly larger, and the overall value is about 15% higher than σx, which is related to length-to-width ratio of mold plate (1.33) and position of gating system. Stress gradient in shallow surface layer (0-15 mm) measured by blind hole method was approximately 1.2 MPa/mm. Stress difference between surface layer (0-5 mm) and subsurface layer (10-15 mm) was approximately 35% of that in surface layer. Stress level decreased significantly below 30 mm depth, with stress amplitude in central layer (at a depth of 160 mm) being less than 8% of that in surface layer [Fig. 5(c)]. Initial stress field of QT600-3 blank exhibited significant spatial asymmetry and gradient characteristics, which were source of disturbance for subsequent finishing deformation control.
injection-molded parts 
Fig. 5 Initial residual stress distribution of mold plate blank
For ease of comparison, σx was measured at 9 grid points on upper surface of mold plate before and after finishing, both for blank and after finishing using traditional methods (4000 r/min, 0.14 mm, 0.6 mm, U-feed, C1 clamping) [Fig. 5(d)]. Results show that σx distribution range of blank is -45~28 MPa; after finishing, σx distribution pattern is reversed—four corners change from areas with smaller compressive stress amplitudes to areas with the largest, while compressive stress amplitude in center decreases. This indicates that machining cutting stress significantly superimposes on stress field of mold plate surface, and original initial stress distribution is "rewritten". Critical region of stress reversal before and after machining is located about 400 mm from center of mold plate, indicating that tool path has a "reshaping" effect on final stress distribution.

2.2 Influence of Process Parameters on Residual Stress on Machined Surface

After establishing initial stress field, this paper analyzes influence of CNC machining parameters on surface stress through single-factor simulation. Except for parameter to be studied, all other parameters are fixed at the middle level of Table 3 in Section 1.6 to eliminate interference of multi-factor coupling. Influence of process parameters on residual stress on machined surface is shown in Figure 6.
injection-molded parts 
Figure 6 Influence of CNC Machining Parameters on Residual Stress and Deformation of Machined Surface
Figure 6(a) shows influence of spindle speed n on |σmax| and δmax. With fixed parameters fz=0.10 mm, ae=0.4 mm, and ap=1.5 mm, as rotational speed increased from 2000 r/min to 6000 r/min, |σmax| increased from 86 MPa to 186 MPa, while δmax decreased from 0.218 mm to 0.152 mm. This is due to increased strain rate sensitivity of material under high-speed cutting, more uniform plastic flow, and a greater thermoplastic compression effect on surface layer under thermo-mechanical coupling. Temperature field analysis shows that when rotational speed increases from 2000 r/min to 6000 r/min, peak temperature in tool-workpiece contact area increases from 187 ℃ to 286 ℃; temperature rise causes thermoplastic deformation, resulting in volume expansion of surface material. After cooling, surface layer shrinkage strain is greater than that of subsurface layer, forming a greater compressive stress.
Figure 6(b) shows effect of feed per tooth fz on |σmax| and δmax. With fixed parameters n=4000 r/min, ae=0.4 mm, and ap=1.5 mm, as fz increases from 0.08 mm to 0.20 mm, |σmax| decreases from 175 MPa to 101 MPa, and δmax increases from 0.124 mm to 0.197 mm. Increasing feed rate increases cutting thickness and cutting force, leading to a wider stress release range and a decrease in compressive stress amplitude as plastic deformation zone deepens. Simultaneously, increased cutting force exacerbates low-frequency vibrations in system, causing δmax to rise. Spectral analysis reveals that when fz increases from 0.08 mm to 0.20 mm, main cutting force increases from 487 N to 912 N (an increase of 87%), low-frequency vibration amplitude increases by 42%, further intensifying deformation. A smaller fz should be used.
Figure 6(c) shows effect of radial cutting width ae on |σmax| and δmax. With fixed parameters n=4000 r/min, fz=0.10 mm, and ap=1.5 mm, as ae increases from 0.2 mm to 1.0 mm, |σmax| first rises from 168 MPa to 192 MPa (ae=0.6 mm) and then decreases to 139 MPa, while δmax monotonically increases from 0.121 mm to 0.213 mm. A smaller ae results in insufficient chip formation, with plowing becoming dominant material movement, and compressive stress is suppressed. When ae is too large, cutting heat increases sharply, and tensile stress component caused by temperature rise partially offsets compressive stress. Cutting force fluctuation amplitude is smallest when ae=0.6 mm. Recommended range for ae is 0.5~0.7 mm.

2.3 Molecular Weight Analysis

To study influence of different toolpath strategies on machining deformation, this section conducts comparative simulations of four toolpath strategies and three clamping schemes.
2.3.1 Tool Path Strategies
Four tool path strategies were compared: unidirectional tool path (U), reciprocating tool path (B), symmetrical layered tool path (S1), and helical equal-height tool path (S2). Results are shown in Figure 7. Maximum δmax for strategy U was 0.218 mm; for strategy B it was 0.184 mm; for strategy S1 it decreased to 0.091 mm, a 58% reduction compared to strategy U; and for strategy S2 it was 0.112 mm. Superiority of S1 strategy stems from its symmetrical load distribution—tool advances symmetrically from center outwards to four corners, and stress release effects of each material removal step cancel each other out, effectively suppressing warping caused by asymmetrical initial stress release. S1 strategy increases machining time by approximately 8% compared to B strategy, but its deformation control effect is significantly better than the other three strategies.
injection-molded parts 
Figure 7: Machining deformation cloud diagrams under four tool path strategies
S1 strategy uses mold plate center as origin of symmetry and divides machining area into four symmetrical quadrants according to principle of "inside first, then outside, radiating layer by layer." Tool advances from symmetry boundary line to outer edge of each quadrant, making torque of cutting force about mold plate's centroid approach zero at each step. In C2 clamping scheme, six clamping plates are symmetrically distributed at 120° along long side of mold plate (two on each long side and one on each short side). Clamping force is dynamically adjusted by CNC system based on real-time deformation monitoring data (0.4~0.8 MPa), as shown in Figure 8.
injection-molded parts 
Figure 8. Schematic diagram of coordinated arrangement of symmetrical layered tool path S1 and six-point symmetrical clamping C2
2.3.2 Clamping Scheme
Three clamping methods were studied and compared: four-point corner clamping (C1), six-point symmetrical clamping (C2), and bottom vacuum + side clamping plate combination clamping (C3). Results are shown in Figure 9. Maximum clamping force δmax of C1 is 0.156 mm, and middle of mold plate is concave; clamping force of C2 is 0.094 mm, and stress distribution is the most uniform; clamping force of C3 is 0.121 mm, but four corners of mold plate are locally warped due to insufficient vacuum suction. Considering both processing stability and clamping efficiency, scheme C2 was selected. Core advantage of scheme C2 is that clamping force of six clamping plates is symmetrically distributed at 120°, avoiding disadvantages of concavity in the middle of scheme C1 and insufficient suction at four corners of scheme C3. Under scheme C2, stress distribution between bottom surface and fixture is more uniform, maximum contact stress decreases from 28 MPa to 19 MPa, and contact area increases from 62% to 78%.
injection-molded parts 
Figure 9. Deformation cloud map under three clamping schemes

2.4 Residual stress prediction and process parameter optimization based on CNN-LSTM

2.4.1 Accuracy of CNN-LSTM model
This paper uses simulation dataset (450 sets, training/validation/test = 360/45/45) for CNN-LSTM training. Training set parameters are sampled using Latin hypercube sampling, and initial stress field is randomly perturbed within measured range (-45~28 MPa) in Section 1.3, with a perturbation amplitude within ±30% (σx amplitude -58~36 MPa) to cover initial stress fluctuation range of same batch of blanks in enterprise. R² values for training and test sets were 0.974 and 0.961, respectively, RMSE values were 7.3 MPa and 8.9 MPa, respectively [Figure 10(a)]. Model can accurately predict processing stress under different parameters.
injection-molded parts 
Figure 10 Comparison and verification between ABAQUS simulation prediction and XRD measurement (QT600-3 mold plate)
2.4.2 Verification of prediction accuracy of simulation model
To evaluate quantitative prediction accuracy of ABAQUS thermo-mechanical coupling model in Section 1.4, three characteristic measurement points (P1 center, P2 quarter diagonal, P3 edge) were selected on QT600-3 mold plate. ABAQUS simulation prediction and X-ray diffraction (XRD) were used for measurement to obtain maximum compressive stress amplitude on processed surface. XRD tests were performed on a Bruker D8 Discover diffractometer with a Cu-Kα target and sin²ψ method (ψ = 0°, 15°, 30°, 45°) using (211) diffraction plane. Sampling area was 1 mm * 1 mm. ABAQUS simulations were performed using method described in Section 1.4, and maximum compressive stress amplitude at corresponding depth (0.05 mm below surface) was extracted at three measurement points. As shown in Figure 10, simulated predicted values for three measurement points were 148.5, 132.7, 165.3 MPa, respectively, while corresponding measured XRD values were 137.2, 119.4, and 147.1 MPa, with an average relative error of 9.5% (7.6%–12.4%), indicating that simulation model can accurately predict residual stress on processed surface.
Main sources of error are following simplified assumptions in model: ① nonlinear effect of cutting temperature on material constitutive structure (which may introduce a deviation of 5% to 8%); ② influence of microstructure evolution of QT600-3 ductile iron on yield strength during cutting process (change in pearlite/ferrite ratio causes differences in strain hardening); ③ mesh convergence; ④ difference between workpiece clamping simplified to an ideal clamping boundary and actual contact stiffness (25%). Considering above factors, average relative error of 9.5% is within acceptable range for engineering (<15%), verifying reliability of simulation model for process optimization.
2.4.3 NSGA-GWO Multi-Objective Optimization
Using CNN-LSTM as surrogate and Equation (3) as objective function, NSGA-GWO optimizer is used for optimization. After 200 iterations, Pareto front solution distribution is shown in Figure 11(b). σσ and δmax are approximately positively correlated—stress standard deviation increases when maximum deformation decreases. Mechanism is as follows: When optimization objective tends to minimize maximum deformation, algorithm preferentially selects combinations such as "light cutting, slow movement, and symmetrical tool movement." However, initial stress field of QT600-3 blank has a significant asymmetric distribution (stress difference between four corners of P1/P3/P7/P9 and center of P5 > 70 MPa). Although symmetrical tool movement can suppress overall warping, it cannot completely "rewrite" asymmetry, leading to increased differences in stress release at different locations and a rise in standard deviation. Large injection molding mold plate have high stiffness and small deformation, making contradiction of stress uniformity more prominent. It is necessary to use σσ and δmax as optimization objectives simultaneously. TOPSIS method is used to screen comprehensive optimal solution from Pareto front solution, σσ and δmax are assigned equal weights of 0.5. Corresponding parameters: n=5 200 r/min, fz=0.09 mm, ae=0.5 mm, D=32 mm, ap=1.2 mm, σσ=11 MPa, δmax=0.083 mm. Compared with a single-target reference process (empirical parameters of 4000 r/min, 0.14 mm, 0.6 mm, φ32 mm, and 1.5 mm), NSGA-GWO joint optimization reduced deformation from 0.158 mm to 0.083 mm (47.5%), and stress standard deviation from 27 MPa to 11 MPa (59.3%).
injection-molded parts 
Figure 11. CNN-LSTM prediction model and NSGA-GWO optimization results

2.5 Processing Example Verification

To verify effectiveness of proposed method, two blanks (M1 and M2) were randomly selected from five QT600-3 blanks (M1~M5) in same batch for comparison. Blanks were confirmed to be defect-free by visual inspection and ultrasonic testing, with initial stresses ranging from -43 to 30 MPa and inter-group differences within ±3 MPa, could be considered homogeneous samples. Before processing, blanks were placed in a constant-temperature workshop at (20±1) ℃ for 24 h. M1 was machined using a traditional process (4000 r/min, 0.14 mm, 0.6 mm, U-shaped feed, C1 clamping), while M2 used an optimized process (5200 r/min, 0.09, 0.5 mm, φ32 mm, 1.2 mm, S1 feed, C2 clamping). Both tools were carbide-coated end mills (φ32 mm, 4 teeth), using the MQL method (50 mL/h emulsion), consistent with simulation conditions in Section 2.2. After machining, CMM was used to check flatness of 16-point mesh; LXRD was used to check stress at 9 corresponding measuring points.
Measured results after processing (Table 4) are as follows: M1 (traditional process): flatness 0.156 mm, σx distribution -178~-86 MPa (σσ=31 MPa), processing time 8.5 h, wear 0.12 mm; M2 (optimized process): flatness 0.078 mm (16-point grid), σx distribution -159~-112 MPa (σσ=12 MPa), processing time 7.1 h, wear 0.03 mm. Compared with traditional process, optimized process reduces flatness by 50.0%, σσ by 61.3%, increases efficiency by 16.5%, and reduces wear by 75.0%. Relative error between stress standard deviation of M2 and simulation prediction (11 MPa) is 8.3%, verifying reliability of NSGA-GWO optimization results. Significant reduction in tool wear is due to: (1) feed per tooth of M2 (0.09 mm) is less than that of M1 (0.14 mm), resulting in a reduction of approximately 36% in cutting thickness per tooth; (2) symmetrical feed of S1 provides a more uniform cutting force distribution than unidirectional feed of U; (3) six-point symmetrical clamping of C2 provides higher contact stiffness (approximately 25%) than four-point angular clamping of C1. Flatness meets design requirement of within 0.10 mm. Figure 12(b) shows actual workpiece after machining with M2, with no visible defects on the surface and Ra=0.8 μm.
Indicators M1 (Traditional Process) M2 (Optimized Process) Improvement Amount
Flatness/mm 0.156 0.078 50.0%
σx Distribution Range/MPa -178--86 -159--112 Significantly Improved Uniformity
σx Standard Deviation σσ/MPa 31 12 61.3%
Machining Time/h 8.5 7.1 16.5%
Tool Wear/mm 0.12 0.03 75.0%
Ra/um 1.2 0.8 33.3%
Table 4 Comparison of machining test results between traditional and optimized processes
injection-molded parts 
Figure 12 Machining test results and inspection results of QT600-3 large injection molding mold plates
Figure 13 shows comparison of surface stress and maximum deformation of mold plate before and after optimization. Based on comparison results of M1 and M2 in this section, after optimization, σσ decreased by 61.3%, δmax decreased by 50.0%, and wear decreased by 75.0%. Before optimization, finishing time for a single mold plate was 8.5 h, which was reduced to 7.1 h after optimization, resulting in a 16.5% increase in efficiency. This verifies comprehensive advantages of proposed method in terms of accuracy, efficiency, and tool life.
injection-molded parts 
Figure 13. Comparison of residual stress and deformation before and after optimization
To evaluate impact of post-processing stress on performance, this paper conducted an ABAQUS/Standard simulation service loading test based on measured stress fields of M1 and M2. Processing stress was applied to mold plate as an initial condition, and static analysis was performed under a 5000 kN clamping force (based on typical clamping force of a 1600 mm injection molding machine). Simulation results show that maximum principal stress decreased from 137 MPa in unoptimized (M1 simulation) to 92 MPa in optimized (M2 simulation), stress concentration area shifted from four corners to around central tie rod hole, and maximum principal stress amplitude decreased by 32.9%. 9-point σx statistical analysis: Before optimization, range was 89 MPa, IQR = 53 MPa, and CV = 24.8%; after optimization, range was 47 MPa, IQR = 28 MPa, and CV = 8.6%, indicating improved stress uniformity.

3 Application

Based on above research, proposed method was extended to machining of moving mold plate (1800 mm * 1400 mm * 380 mm, approximately 44% larger than laboratory verification specifications in Section 2.5) of a certain model of new energy vehicle front bumper mold. Initial stress tests (-44~29 MPa) were performed on blanks according to method in Section 1.3. Ten pieces (B1~B10) were machined using optimized process, and ten pieces (C1~C10) were machined using traditional process as a control. Optimized group achieved a flatness of ≤0.08 mm (maximum 0.076 mm), a tie rod hole position accuracy of ≤0.03 mm, Ra≤0.9 μm, and a 100% first-pass yield, meeting accuracy grade 1 requirements of GB/T 12556-2006 (Technical Conditions for Plastic Injection Mold Mold plates). Traditional group had an average flatness of 0.155 mm, with 3 pieces exceeding 0.15 mm tolerance (30% rework rate). Optimized group saved approximately 600 yuan per piece in labor costs, tooling costs, and rework amortization costs (180 yuan per piece). Based on an annual production of 1200 pieces, this translates to annual savings of approximately 720,000 yuan. See Table 5 for details.
Indicators Optimized process (Group B) Traditional process (Group C) Improvement rate/%
Flatness/mm 0.070 0.155 54.8
Flatness pass rate/% 100 70 30
Binding rod hole position accuracy/mm 0.020 0.034 41.2
Ra/um 0.8 1.2 33.3
Machining time (h) 7.1 8.5 16.5
Tool wear/mm 0.03 0.12 75.0
Rework rate/% 0 30 -
Table 5 Comparison of Batch Production Results between Optimized and Traditional Processes (Average of 10 Pieces per Group)

4 Verification through Repeated Experiments

To evaluate repeatability of proposed method, five repeated processing experiments were conducted on both traditional process (M1) and optimized process (M2) under same process parameters and blank conditions (QT600-3 mold plate, specifications 1600 mm * 1200 mm * 320 mm). Maximum deformation, flatness error, and standard deviation of surface stress of each mold plate were measured, and results are shown in Figure 14. In five repeated experiments, maximum deformation of traditional process was (0.156 ± 0.008) mm, while that of optimized process was (0.078 ± 0.003) mm; flatness error decreased from (0.062 ± 0.006) mm to (0.028 ± 0.003) mm; and standard deviation of stress decreased from (28.4 ± 1.4) MPa to (10.7 ± 0.6) MPa. All three indicators show that optimized process significantly improves upon traditional process (49.9%–62.4%), with low data dispersion (coefficient of variation CV < 8%), indicating good reproducibility of proposed method. Furthermore, statistical results of five repeated experiments are largely consistent with data in Table 4 (representative single experiment) and Table 5 (batch production of 10 blocks per group), further validating engineering reliability of proposed method.
injection-molded parts 
Figure 14 Statistical results of repeated machining experiments

5 Conclusion

(1) Taking QT600-3 large injection molding mold plate as research object, this study investigated machining deformation and out-of-tolerance problems caused by destruction of initial residual stress equilibrium state of blank (material removal) and combined effect of cutting additional stress. XRD and blind hole methods were used to reveal that initial stress field of mold plate has significant spatial asymmetry (-45~28 MPa) and a gradient in shallow surface thickness direction (approximately 1.2 MPa/mm). This verified that combined effect of initial stress and cutting additional stress is fundamental cause of mold plate deformation. Based on this, influence of spindle speed, feed per tooth, radial cutting width, tool path strategy, and clamping scheme on stress and deformation of machined surface was analyzed using ABAQUS thermo-mechanical coupling simulation system. Results showed that when spindle speed increased from 2000 r/min to 6000 r/min, maximum compressive stress amplitude increased from 86 MPa to 186 MPa, and feed per tooth increased from 0.08 mm to 0.20 mm. When diameter is 0.5 mm, compressive stress amplitude decreases by about 42%, and radial cutting width of 0.6 mm is optimal; symmetrical cutting reduces deformation by 58% compared with unidirectional cutting, six-point symmetrical clamping reduces deformation by 40% compared with four-point corner clamping, which is an effective process combination for stress control of large mold plate;
(2) A CNN-LSTM prediction model (R²=0.961) was further constructed, and combined with NSGA-GWO joint optimization, maximum deformation decreased from 0.158 mm to 0.083 mm, and stress standard deviation decreased from 27 MPa to 11 MPa. Finally, proposed method was applied to machining of moving mold plate of a front bumper mold for a certain model of new energy vehicle with specifications of 1800 mm * 1400 mm * 380 mm. Flatness of all 10 mold plate in optimized group was ≤0.08 mm (maximum 0.076 mm), position accuracy of tie rod hole was ≤0.03 mm, Ra≤0.9 μm, and the first-pass yield was 100%. This significantly reduced 30% rework rate compared to traditional group, saving approximately 600 yuan per mold plate and increasing efficiency by 16.5%. Based on an annual production of 1200 mold plate, this translates to an annual saving of approximately 720,000 yuan, validating comprehensive advantages of proposed method in terms of accuracy, efficiency, and tool life.
(3) This "measurement-simulation-control" process paradigm can also provide theoretical reference and practical guidance for deformation control and residual stress management of large parts such as large castings and welded components.

Go To Top