Arc Core Pulling Mechanism

Time:2026-11-12 08:58:25 / Popularity: / Source:

1. Angled Guide Pillar Driven Arc Core Pulling

Figure 9-57 shows a mold example of direct core pulling using angled guide pillars on an arc-shaped cover. When radius of curvature of arc within parting surface of plastic part is large, angled guide pillars can be used for direct core pulling. Angled guide pillar hole on slider needs to be machined into an elongated hole. Slider's movement track is concentric with arc of plastic part. Angled guide pillar arc core pulling structure is simple and has low mold cost.
Arc Core Pulling Mechanism 
Figure 9-57 Angled guide post driven circular arc core pulling

2. Connecting Rod Driven Arc Core Pulling

Maximum external dimensions of massager cable ring product are 57.50mm x 54.10mm x 25.10mm, average thickness of plastic part is 2.70mm, plastic part material is PVC, as shown in Figure 9-58. Main body of plastic part is shaped like a bull's horn, with an arc-shaped through hole in the middle. Diameter of hole at large end is 6.50mm, edge of bull's horn shape is a thin sheet with a hole. Arc-shaped through-hole at the center of plastic part has a radius of R106mm in horizontal plane. Difficulty in mold design lies in demolding this arc-shaped through-hole.
Massager's cable ring is made of rigid PVC. Its internal arc-shaped through-hole requires rotating mold core for demolding. When determining mold design, mold opening direction must first be determined. Mold parting surface is relatively simple, being a plane. Analysis shows that plastic part is relatively small; placing it horizontally and rotating inner core in horizontal plane is more convenient. Whether to rotate in horizontal or vertical plane depends on size and structure of plastic part. For example, shower head handle has a more complex structure and often rotates in vertical plane.
Inner core of arc-shaped through-hole is demolded by a slider with an arc-shaped core-pulling mechanism. Guide block 11 guides slider insert 13 through its arc-shaped inner hole. Slider insert 13 is fixed to slider 10, and slider 10 slides along arc-shaped track, causing slider insert 13 to be pulled out for demolding. During mold opening, inclined guide post 3 drives slider seat 6 to move. Slider 10 is driven by connecting rod 8. After tightening pivot screw 5, it is necessary to ensure that connecting rod 8 can rotate freely. After mold opening, plastic part is removed manually. Due to structural reasons, shape of plastic part does not allow for design of ejector pins.
This mold design is novel and ingenious, simplifying complex problem of arc core pulling into a simple slider core pulling.
Arc Core Pulling Mechanism 
Figure 958 Horizontal Arc Core-Pulling Mechanism with Connecting Rod
1 - Cavity; 2 - Plate A; 3 - Inclined Guide Post; 4 - Inclined Wedge; 5 - Shaft Screw; 6 - Slider Seat; 7 - Positioning Ball; 8 - Connecting Rod; 9 - Plate B; 10 - Slider; 11 - Guide Block; 12 - Core; 13 - Slider Insert
Strawberry box mold is shown in Figure 9-59. Maximum external dimensions of product are 360.49mm x 330.67mm x 85.83mm, average thickness of plastic part is 2.50mm, material is ABS, and weight of plastic part is 490.62g. Difficulty in mold design lies in arc undercut on one side edge of plastic part, which requires rotating slider for core pulling. There is also an undercut on the inside of arc undercut, requiring design of a large lifter.
Due to large size of plastic part, mold cavity layout is 1-to-1, and plastic part is injected through a single hot runner from top center of plastic part. Mold base is a non-standard 7575, and injection molding machine is a Mitsubishi 650t injection molding machine.
Mold design is shown in Figure 9-59. Undercut slider has an undercut of 18.4mm, a slider stroke of 21.5mm, and is driven by inclined guide pillars. Inclined guide pillars have an inclination angle of 13° and a diameter of 630mm, while slider width is 342mm. Due to slider's width, two inclined guide pillars are used for driving. Wear-resistant plates are added to slider's inclined surface, and an 11mm cooling circuit is designed on slider for cooling. These two sliders are positioned horizontally using two ball bearings.
Before moving, slider needs to rotate to disengage from arc-shaped locking position. Three hydraulic cylinders are used here to achieve core-pulling action. Rotating swing hydraulic cylinder has a slider stroke of 48mm and a cylinder stroke of 50mm; large slider moving hydraulic cylinder has an undercut of 37.2mm, a slider stroke of 41mm, and a cylinder stroke of 50mm; bottom locking slider has a stroke of 66mm and a cylinder stroke of 70mm. All sliders are rear mold sliders. After mold opening, piston rod of locking cylinder 14 retracts first, releasing lock. Then, rotating core-pulling cylinder, through piston rod 8, drives pin 10 to push rotating slider 4 around the center, thus achieving arc-shaped core pulling. Pin 10 can slide in groove of slider 4. After arc-shaped core pulling is completed, large slider moving cylinder drives large slider to complete the entire core-pulling action. This large cylinder is a double-axis cylinder, and nut at tail triggers a limit switch to control cylinder stroke. Small cylinder and its rotating slider are fixed to bottom of large cylinder slider. During mold closing, large slider first resets, then rotating core-pulling cylinder resets, and finally locking cylinder locks.
Slider and lifter are both relatively wide, and cooling water pipe is relatively long. A cooling circuit support is designed to facilitate support of cooling system.
Arc Core Pulling Mechanism 
Figure 9-59 Design of Rotary Core-Pulling Mold for Strawberry Box
1. Fixed Mold Base Plate; 2. Plate A; 3. Large Slider; 4. Rotary Slider; 5. Inclined Ejector Assembly; 6. Rotary Core-Pulling Cylinder Fixing Plate; 7. Locking Block; 8. Piston Rod; 9. Core; 10. Pin; 11, 13. Inclined Ejector Guide Plate; 12. Plate B; 14. Locking Cylinder; 15. Inclined Ejector Seat; 16. Push Rod Fixing Plate; 17. Push Plate; 18. Moving Mold Base Plate; 19. Water Pipe Fixing Seat; 20. Water Pipe; 21. Oil Pipe Fixing Seat; 22, 23, 25. Oil Pipe; 24. Cylinder Bracket; 26. Large Cylinder Piston Rod; 27. Cylinder Connector; 28. Cylinder Connector Pressure Plate; 29. Large Slider Seat; 30. Wear-Resistant Plate

3. Gear and rack driven arc-shaped core pulling

Gear and rack driven arc-shaped core pulling is the most common arc-shaped core-pulling mechanism. Rack and pinion driven arc-shaped core-pulling mechanism features reliable operation, precise position control, flexible selection of drive mechanism design direction and method. Figure 9-60 shows design of an arc-shaped core-pulling mold for oral cavity tubes. The entire mold uses a rack and pinion arc-shaped core-pulling system. Oral cavity tube is an arc-shaped dropper for oral medication administration. Product is very small, made of PP, and has a 1-outlet, 16-cavity arrangement in two symmetrical rows. After mold opening, wedge drives locking slider 11 to pull core through the T-slot. Slider seat 9 is released, and rack 21 drives large gear 18 to rotate clockwise. Small gear 17 on same axis drives swing gear 16 to swing counterclockwise. Slider seat 9 is fixed to swing gear 16, achieving arc-shaped core pulling through arc-shaped swing.
Arc Core Pulling Mechanism 
Figure 9-60 Design of Arc Core-Pulling Mold for Oral Bend Tube
1 - Pull Rod; 2 - Flow Channel Push Plate; 3 - Small Pull Rod Assembly; 4 - Spring; 5 - Cavity; 6 - Fixed Mold Base Plate; 7 - Wedge; 8 - Slider Arc Insert; 9 - Slider Seat; 10 - Plate A; 11 - Locking Slider; 12 - Shaft Seat; 13 - Plate B; 14 - Pad Plate; 15 - Push Rod; 16 - Swing Gear; 17 - Small Gear; 18 - Large Gear; 19 - Limit Switch Seat; 20 - Limit Switch; 21 - Rack

Go To Top