Branch Runner Design
Time:2026-11-09 09:15:16 / Popularity: / Source:
A branch runner is a feeding channel connecting main runner and gate. Runners are essential in multi-cavity molds, while they can sometimes be omitted in single-cavity molds. In multi-cavity molds that mold multiple parts in one molding process and in single-cavity molds with multiple injection points for producing large products, runners must be installed to distribute material from main runner to each gate. Runners are a crucial component of gating system in multi-gate molds, significantly impacting filling and holding pressure process. In ordinary two-plate mold gating systems, runners are generally located on parting surface; in ordinary three-plate mold gating systems, runners are typically located on parting surface itself, between cavity plate and runner ejector plate, to facilitate removal of solidified material from runner during mold opening.
I. Key Considerations for Branch Runner Design
Since branch runner guides high-temperature, high-pressure molten plastic from main runner to gate and into mold cavity, design must minimize not only temperature drop and pressure loss of melt as it passes through runner, but also ensure a smooth and even distribution of melt to each cavity. Therefore, appropriate and reasonable runner shape and size should be determined by comprehensively considering factors such as volume of product, wall thickness, shape complexity, number of cavities, and properties of plastic used.
Sometimes branch runners are only located in fixed mold or moving mold; other times, they are located in both fixed and moving molds (forming various cross-sectional shapes after mold closing). This depends on mold structure and properties of plastic. Having runners in both fixed and moving molds is beneficial for material flow and is often used for plastics with poor flowability. Widespread use of CNC machining centers makes runner machining very easy; even curved and arc-shaped runners are not difficult to machine. In three-plate molds, runners are located on one side of cavity plate. When a runner system needs to be switched, runner should also be located on one side of mold plate. Sometimes, a runner pull rod or ejector rod is required to facilitate demolding of solidified material.
1. Plastic Flowability and Product Shape: For plastics with poor flowability, such as PC, PSU, PMMA, and PEEK, runner should be as short as possible. Rounded transitions should be used where runner bends occur. A larger cross-sectional area is preferable, and cross-sectional shape should be circular or U-shaped.
Direction and cross-sectional shape of runner depend on location and number of gates, which in turn depend on product shape. If there are many runners, a cold slug well should be considered to prevent molten plastic from directly impacting cavity and to avoid sharp turns, ensuring a smooth transition. Runners are generally distributed in a balanced manner; in special cases, an unbalanced method can be used. Goal is to ensure simultaneous and even injection into each cavity, with a compact arrangement and short flow path to reduce mold size. Runner design of exit mold should comply with mold design specifications.
2. Number of Cavities: Number of cavities determines direction, length, and size of runners. Runners should be compactly arranged with reasonable spacing, generally using axisymmetric or centrosymmetric methods to achieve balance and minimize the total area of molding zone. Ideally, geometric center of the total projection of cavities and runners on parting surface should coincide with center of clamping force.
3. Wall Thickness and Appearance Requirements: Wall thickness, appearance requirements, and internal quality requirements determine location and form of gate, ultimately determining direction and cross-sectional parameters of runners.
4. Injection Molding Machine Pressure and Injection Speed: While meeting injection molding process requirements, cross-sectional area of runners should be as small as possible. However, excessively small runner cross-sectional areas will reduce injection speed, prolong filling time, and may lead to defects such as short runs, burning, and shrinkage cavities. Conversely, excessively large runners will increase amount of solidified material in runners, wasting material and prolonging cooling time. Generally, after injection molding, runner system is last part to cool. Cooling time of runners should not exceed cooling time of part in cavity to avoid affecting injection efficiency. Therefore, mold design should incorporate experience from similar plastic parts, using a smaller cross-sectional area and verifying its feasibility through mold flow analysis.
When possible, length of runners should be as short as possible to reduce pressure loss. In multi-cavity molds, runner lengths of each cavity should be as equal as possible to achieve pressure balance during injection, ensuring that plastic fills each cavity as simultaneously and evenly as possible. In some cases where runner lengths cannot be equal, necessary compensation measures should be taken at gate. A cold slug well should be provided at the end of runner to prevent cold slug and air from entering cavity.
Number of turns in runner should be minimized. Turns should have rounded corners, as shown in Figure 5-14, avoiding sharp corners. This facilitates plastic flow and reduces pressure loss. A cold slug well should also be provided at each runner bend. A chamfer must be provided in cold slug well, and ejector pin length below cold slug well must be shortened. Main runner must be polished and have sufficient roughness. Venting and pressure reduction should be implemented in runner and cavity at final filling point and any point of change in direction.
Sometimes branch runners are only located in fixed mold or moving mold; other times, they are located in both fixed and moving molds (forming various cross-sectional shapes after mold closing). This depends on mold structure and properties of plastic. Having runners in both fixed and moving molds is beneficial for material flow and is often used for plastics with poor flowability. Widespread use of CNC machining centers makes runner machining very easy; even curved and arc-shaped runners are not difficult to machine. In three-plate molds, runners are located on one side of cavity plate. When a runner system needs to be switched, runner should also be located on one side of mold plate. Sometimes, a runner pull rod or ejector rod is required to facilitate demolding of solidified material.
1. Plastic Flowability and Product Shape: For plastics with poor flowability, such as PC, PSU, PMMA, and PEEK, runner should be as short as possible. Rounded transitions should be used where runner bends occur. A larger cross-sectional area is preferable, and cross-sectional shape should be circular or U-shaped.
Direction and cross-sectional shape of runner depend on location and number of gates, which in turn depend on product shape. If there are many runners, a cold slug well should be considered to prevent molten plastic from directly impacting cavity and to avoid sharp turns, ensuring a smooth transition. Runners are generally distributed in a balanced manner; in special cases, an unbalanced method can be used. Goal is to ensure simultaneous and even injection into each cavity, with a compact arrangement and short flow path to reduce mold size. Runner design of exit mold should comply with mold design specifications.
2. Number of Cavities: Number of cavities determines direction, length, and size of runners. Runners should be compactly arranged with reasonable spacing, generally using axisymmetric or centrosymmetric methods to achieve balance and minimize the total area of molding zone. Ideally, geometric center of the total projection of cavities and runners on parting surface should coincide with center of clamping force.
3. Wall Thickness and Appearance Requirements: Wall thickness, appearance requirements, and internal quality requirements determine location and form of gate, ultimately determining direction and cross-sectional parameters of runners.
4. Injection Molding Machine Pressure and Injection Speed: While meeting injection molding process requirements, cross-sectional area of runners should be as small as possible. However, excessively small runner cross-sectional areas will reduce injection speed, prolong filling time, and may lead to defects such as short runs, burning, and shrinkage cavities. Conversely, excessively large runners will increase amount of solidified material in runners, wasting material and prolonging cooling time. Generally, after injection molding, runner system is last part to cool. Cooling time of runners should not exceed cooling time of part in cavity to avoid affecting injection efficiency. Therefore, mold design should incorporate experience from similar plastic parts, using a smaller cross-sectional area and verifying its feasibility through mold flow analysis.
When possible, length of runners should be as short as possible to reduce pressure loss. In multi-cavity molds, runner lengths of each cavity should be as equal as possible to achieve pressure balance during injection, ensuring that plastic fills each cavity as simultaneously and evenly as possible. In some cases where runner lengths cannot be equal, necessary compensation measures should be taken at gate. A cold slug well should be provided at the end of runner to prevent cold slug and air from entering cavity.
Number of turns in runner should be minimized. Turns should have rounded corners, as shown in Figure 5-14, avoiding sharp corners. This facilitates plastic flow and reduces pressure loss. A cold slug well should also be provided at each runner bend. A chamfer must be provided in cold slug well, and ejector pin length below cold slug well must be shortened. Main runner must be polished and have sufficient roughness. Venting and pressure reduction should be implemented in runner and cavity at final filling point and any point of change in direction.
Figure 5-14 Rounded corners and cold material pockets added at branch channel turning points
5. Pulling and Removing Methods for Main and Sub-runners: When sub-runner is located on fixed mold side or extends for a long time, pull rods should be installed near gate or at intersection of sub-runners.
6. Runner Solidification: Solidification of runner should be slightly later than solidification of product to facilitate pressure transmission and holding.
7. Surface Roughness: Inner surface roughness Ra of sub-runner should be 1.6 μm. This reduces flow of outer layer of material under frictional resistance of runner, fixes cooling skin of runner, is beneficial for heat preservation of molten plastic. In practice, ordinary runners are polished with #320 sandpaper, while runner systems for mirror-finish products must be polished with #600 sandpaper.
5. Pulling and Removing Methods for Main and Sub-runners: When sub-runner is located on fixed mold side or extends for a long time, pull rods should be installed near gate or at intersection of sub-runners.
6. Runner Solidification: Solidification of runner should be slightly later than solidification of product to facilitate pressure transmission and holding.
7. Surface Roughness: Inner surface roughness Ra of sub-runner should be 1.6 μm. This reduces flow of outer layer of material under frictional resistance of runner, fixes cooling skin of runner, is beneficial for heat preservation of molten plastic. In practice, ordinary runners are polished with #320 sandpaper, while runner systems for mirror-finish products must be polished with #600 sandpaper.
II. Branch Runner Types
1. Branch Runner System for Two-Plate Molds: Typical runner system design dimensions for a two-plate mold are shown in Figure 5-15. As can be seen from figure, left side represents size of injection molding machine, expressed in tonnage of clamping force. Different injection molding machines correspond to different mold sizes. In same machine tonnage column, four parameters H, I, J, K each have two columns of parameters. Parameters on the left are smaller, suitable for ABS, PS, AS, PP, PE, PA, PC+ABS, PC+PS materials; parameters on the right are larger, suitable for materials with poor flowability, commonly including PM-MA, PVC, POM, PBT, PET, PC, PPS, PSU.
Figure 5-15 Design parameters of runner for a two-plate mold
For small products with a part volume of less than 2cm³, to minimize amount of solidified material in gating system and improve material utilization, size of cold slug well needs to be shortened. Runner system design is shown in Figure 5-16.
For small products with a part volume of less than 2cm³, to minimize amount of solidified material in gating system and improve material utilization, size of cold slug well needs to be shortened. Runner system design is shown in Figure 5-16.
Figure 5-16 Runner design for small plastic parts in a two-plate mold
2. Branch Runner System for Three-Plate Molds: Typical runner system shape for a three-plate mold is shown in Figure 5-17. For narrow runner systems, when a single runner branches into three or more branches, a disc should be made at branch point to facilitate plastic flow. Disc diameter should be 15-25mm, and its depth should be flush with bottom of runner. Both main runner and recessed branch runners are conical, and their dimensions can be designed by referring to main runner dimensions of a two-plate mold. Branch runners need to be designed with a U-shaped or trapezoidal cross-section in horizontal plane. Length of cold slug well in horizontal plane should not be less than three times maximum cross-sectional dimension.
2. Branch Runner System for Three-Plate Molds: Typical runner system shape for a three-plate mold is shown in Figure 5-17. For narrow runner systems, when a single runner branches into three or more branches, a disc should be made at branch point to facilitate plastic flow. Disc diameter should be 15-25mm, and its depth should be flush with bottom of runner. Both main runner and recessed branch runners are conical, and their dimensions can be designed by referring to main runner dimensions of a two-plate mold. Branch runners need to be designed with a U-shaped or trapezoidal cross-section in horizontal plane. Length of cold slug well in horizontal plane should not be less than three times maximum cross-sectional dimension.
Figure 5-17 Runner system of a three-plate mold
Figure 5-18 shows runner dimensions for narrow runner systems. Figure (a) shows a mold base width less than or equal to 350mm; Figure (b) shows a mold base width greater than 350mm but less than 600mm; and Figure (c) shows a mold base width greater than or equal to 600mm.
Figure 5-18 shows runner dimensions for narrow runner systems. Figure (a) shows a mold base width less than or equal to 350mm; Figure (b) shows a mold base width greater than 350mm but less than 600mm; and Figure (c) shows a mold base width greater than or equal to 600mm.
Figure 5-18 Runner dimensions of narrow nozzle
Figure 5-19 shows runner dimensions when converting from a small gate to a large gate. Figure (a) shows a mold base width of 350mm or less; Figure (b) shows a mold base width greater than 350mm but less than 600mm; and Figure (c) shows a mold base width greater than or equal to 600mm. All dimensions for converting from a small gate to a large gate, or to a submarine gate, can be referenced from those for large gate and submarine gate systems. All dimensions will vary depending on size of plastic and part. Because rapid injection is required during runner conversion, gate at conversion joint is larger than a standard point gate, with a minimum diameter of 2mm. For large plastic parts, gate diameter can be appropriately increased, but it should not be too large, otherwise it will be difficult to break.
Converting from a small gate to a large gate is often used when plastic part is very tall and A-plate is thick, to shorten solidification of small gate runner and stroke of gate ejector plate. For large plastic parts with multiple gates, point gates can be designed in some locations, while edge side gates or submarine gates can only be designed in other locations. After mold opening, solidified sprue remaining in moving mold after breaking can be used as a gripper for a robotic arm.
Figure 5-19 shows runner dimensions when converting from a small gate to a large gate. Figure (a) shows a mold base width of 350mm or less; Figure (b) shows a mold base width greater than 350mm but less than 600mm; and Figure (c) shows a mold base width greater than or equal to 600mm. All dimensions for converting from a small gate to a large gate, or to a submarine gate, can be referenced from those for large gate and submarine gate systems. All dimensions will vary depending on size of plastic and part. Because rapid injection is required during runner conversion, gate at conversion joint is larger than a standard point gate, with a minimum diameter of 2mm. For large plastic parts, gate diameter can be appropriately increased, but it should not be too large, otherwise it will be difficult to break.
Converting from a small gate to a large gate is often used when plastic part is very tall and A-plate is thick, to shorten solidification of small gate runner and stroke of gate ejector plate. For large plastic parts with multiple gates, point gates can be designed in some locations, while edge side gates or submarine gates can only be designed in other locations. After mold opening, solidified sprue remaining in moving mold after breaking can be used as a gripper for a robotic arm.
Figure 5-19 Runner dimensions when switching from a narrow nozzle to a large nozzle
3. Branch Runner Design on a Slider: Arrangement of runners on a half-slider is shown in Figure 5-20. This design is suitable for products molded entirely on sliders. All runners are machined on two sliders, and a cold slug well is required below main runner.
3. Branch Runner Design on a Slider: Arrangement of runners on a half-slider is shown in Figure 5-20. This design is suitable for products molded entirely on sliders. All runners are machined on two sliders, and a cold slug well is required below main runner.
Figure 5-20 Runner on half slider
For some injection molded products, location of gate is limited. To facilitate gate design, gate is designed on slider. Figure 5-21 shows runner design of a two-plate mold with runner on the top of slider. An undercut is designed on the top of slider insert 5. During mold opening, runner is pulled out from sprue sleeve by undercut. When slider moves, undercut is pulled out and remains on plastic part. Figure 5-22 shows runner design of a three-plate mold with runner on the top of slider. During mold opening, runner is pulled out from slider, similar to a two-plate mold.
For some injection molded products, location of gate is limited. To facilitate gate design, gate is designed on slider. Figure 5-21 shows runner design of a two-plate mold with runner on the top of slider. An undercut is designed on the top of slider insert 5. During mold opening, runner is pulled out from sprue sleeve by undercut. When slider moves, undercut is pulled out and remains on plastic part. Figure 5-22 shows runner design of a three-plate mold with runner on the top of slider. During mold opening, runner is pulled out from slider, similar to a two-plate mold.
4. Auxiliary Runner: During secondary processing such as laser cutting, electroplating, and runner punching, accurate positioning of plastic part is required, thus necessitating design of an auxiliary runner. Auxiliary runner design is essentially a rectangular frame composed of runner channels, enclosing plastic part within rectangle. Four positioning posts are designed at four corners of rectangle to facilitate stacking of plastic parts, as shown in Figure 5-23. Size L depends on height of plastic part. Auxiliary runners are generally used in small to medium-sized plastic parts, most commonly small parts such as mobile phone buttons. Figure 5-24 shows an auxiliary runner used in electroplating of a family mold.
III. Runner Cross-Section
1. Runner Cross-Section Shape: Common cross-sectional shapes for runners include circular, U-shaped, trapezoidal, semi-circular, regular hexagonal, and rectangular.
To reduce pressure and heat loss within runner, it is desirable to maximize cross-sectional area and minimize internal surface area of runner. For molten plastics of same flow rate, flow resistance and heat loss should be minimized. Efficiency of runner is expressed as ratio of its cross-sectional area S to its perimeter L.
η = S/L. Where: η - efficiency of runner; S - cross-sectional area of runner, mm2; L - perimeter of runner, mm.
Therefore, when selecting cross-sectional shape of runner, efficiency of runner and mold structure should be considered. Flow efficiency and heat loss of runners with different cross-sectional shapes are shown in Table 5-4.
Table 5-4 Flow efficiency and heat loss of runners with different cross-sectional shapes
To reduce pressure and heat loss within runner, it is desirable to maximize cross-sectional area and minimize internal surface area of runner. For molten plastics of same flow rate, flow resistance and heat loss should be minimized. Efficiency of runner is expressed as ratio of its cross-sectional area S to its perimeter L.
η = S/L. Where: η - efficiency of runner; S - cross-sectional area of runner, mm2; L - perimeter of runner, mm.
Therefore, when selecting cross-sectional shape of runner, efficiency of runner and mold structure should be considered. Flow efficiency and heat loss of runners with different cross-sectional shapes are shown in Table 5-4.
Table 5-4 Flow efficiency and heat loss of runners with different cross-sectional shapes
Practice has shown that, with equal cross-sectional areas, square has the longest perimeter, and circle has the shortest. The shorter perimeter, the lower resistance and the less heat loss, thus the higher efficiency. Order of runner efficiency from highest to lowest is: circular, U-shaped, regular hexagonal, trapezoidal, rectangular, and semi-circular.
Considering flow efficiency and heat loss of various cross-sectional shapes, circular, trapezoidal, and U-shaped runners are commonly used.
① Circular runner. Advantages: Smallest surface area, largest volume, and smallest contact area with mold, resulting in low resistance, which facilitates flow of molten material and reduces heat transfer into mold. A hexagonal cross-section runner has similar characteristics to a circular cross-section, but its efficiency is slightly lower, and it is only used in special cases.
② Trapezoidal runner. Advantages: Can be machined on one side of mold, saving time. Main applications: In ordinary two-plate molds, trapezoidal runner is used instead of a circular runner, with runner only on moving mold side; In three-plate molds, runner is machined on the back of fixed mold plate, near runner ejector plate; In molds with ejector plates, the runner can only be made on fixed mold side; In split molds, runner needs to be made on fixed mold side, located on upper surface of slide block.
In above cases, trapezoidal or U-shaped runners are mostly used, while semi-circular runners should be avoided. Width B of a trapezoidal cross-section is typically 4-8mm, height H = (0.66-0.85)B, slope on one side is 5-10, bottom is machined with a 1-2mm radius to facilitate plastic flow and easy demolding.
③ U-shaped runner. U-shaped runners are highly efficient, can be machined on only one side of the mold, are easy to manufacture, and facilitate demolding of solidified material. Therefore, they are the most commonly used in molds and are suitable for designs on complex parting surfaces. They are a preferred choice for automotive molds. Friction and temperature loss between molten material and runner are lower in U-shaped runners than in trapezoidal runners, making them an improvement over trapezoidal runners.
④ Semi-circular and rectangular runners. Semi-circular and rectangular runners are less efficient and are only used in special cases.
2. Runner Cross-Section Dimensions
Cross-sectional dimensions of runner are mainly determined based on plastic's flowability, processing properties, injection rate, part quality, part wall thickness, runner length, and mold structure. Runner diameter range for various plastics is shown in Table 5-5. If a trapezoidal or other shape is used, corresponding parameters can be calculated based on equal areas.
Considering flow efficiency and heat loss of various cross-sectional shapes, circular, trapezoidal, and U-shaped runners are commonly used.
① Circular runner. Advantages: Smallest surface area, largest volume, and smallest contact area with mold, resulting in low resistance, which facilitates flow of molten material and reduces heat transfer into mold. A hexagonal cross-section runner has similar characteristics to a circular cross-section, but its efficiency is slightly lower, and it is only used in special cases.
② Trapezoidal runner. Advantages: Can be machined on one side of mold, saving time. Main applications: In ordinary two-plate molds, trapezoidal runner is used instead of a circular runner, with runner only on moving mold side; In three-plate molds, runner is machined on the back of fixed mold plate, near runner ejector plate; In molds with ejector plates, the runner can only be made on fixed mold side; In split molds, runner needs to be made on fixed mold side, located on upper surface of slide block.
In above cases, trapezoidal or U-shaped runners are mostly used, while semi-circular runners should be avoided. Width B of a trapezoidal cross-section is typically 4-8mm, height H = (0.66-0.85)B, slope on one side is 5-10, bottom is machined with a 1-2mm radius to facilitate plastic flow and easy demolding.
③ U-shaped runner. U-shaped runners are highly efficient, can be machined on only one side of the mold, are easy to manufacture, and facilitate demolding of solidified material. Therefore, they are the most commonly used in molds and are suitable for designs on complex parting surfaces. They are a preferred choice for automotive molds. Friction and temperature loss between molten material and runner are lower in U-shaped runners than in trapezoidal runners, making them an improvement over trapezoidal runners.
④ Semi-circular and rectangular runners. Semi-circular and rectangular runners are less efficient and are only used in special cases.
2. Runner Cross-Section Dimensions
Cross-sectional dimensions of runner are mainly determined based on plastic's flowability, processing properties, injection rate, part quality, part wall thickness, runner length, and mold structure. Runner diameter range for various plastics is shown in Table 5-5. If a trapezoidal or other shape is used, corresponding parameters can be calculated based on equal areas.
To accurately determine runner diameter, there are generally three methods: First method: Determined based on part quality, see Table 5-6; Second method: Determined based on projected area of part on the parting surface, see Table 5-7; Third method: Determining runner diameter based on part's mass, wall thickness, and runner length, as shown in Figures 5-25 and 5-26. Specific process is as follows: a. For PS, ABS, SAN, and other plastic products, runner diameter is determined from Figure 5-25 based on part's mass and wall thickness; b. For PE, PP, PA, PC, POM, and other plastic products, runner diameter is determined from Figure 5-26 based on part's mass and wall thickness; c. After determining runner cross-sectional diameter from Figures 5-25 and 5-26, correction factor f is determined from Figure 5-27 based on runner length L. Final runner diameter D = f × D'; Fourth method: Calculation method. For plastic parts with a wall thickness less than 3mm and a mass less than 200g, runner diameter can be determined using following empirical formula.
In formula: D - diameter of runner, mm; W - mass of plastic part, g; L - length of runner, mm.
Calculated runner diameter range is 3.2~9.5mm. For easily flowing plastics such as PE, PP, and PA, D value can be appropriately reduced. For difficult-to-flow plastics such as PC, PVC, and PMMA, calculated D value needs to be increased by 25% (within 3.2~9.5mm range).
In mold design, three commonly used runner cross-sections are: circular, trapezoidal, and U-shaped. U-shaped cross-section, also called a parabolic cross-section, has varying slopes in different countries and regions, and among different companies. Calculated runner diameter needs to be rounded according to machining tool. Common rounding results are shown in Figure 5-28. Slope of trapezoidal runner (5°) can also be adjusted within the range of 5°~10°.
Calculated runner diameter range is 3.2~9.5mm. For easily flowing plastics such as PE, PP, and PA, D value can be appropriately reduced. For difficult-to-flow plastics such as PC, PVC, and PMMA, calculated D value needs to be increased by 25% (within 3.2~9.5mm range).
In mold design, three commonly used runner cross-sections are: circular, trapezoidal, and U-shaped. U-shaped cross-section, also called a parabolic cross-section, has varying slopes in different countries and regions, and among different companies. Calculated runner diameter needs to be rounded according to machining tool. Common rounding results are shown in Figure 5-28. Slope of trapezoidal runner (5°) can also be adjusted within the range of 5°~10°.
Figure 5-28 Rounded values of runner dimensions
Table 5-5 Distributor Diameters for Different Plastics
Table 5-5 Distributor Diameters for Different Plastics
Tables 5-6 and 5-7 show general runner dimensions for styrene, but these dimensions may need to be adjusted based on characteristics of plastic and shape of product. Calculated runner dimensions need to be revised based on practical experience accumulated from similar mold designs. Computer simulation analysis should be used to arrive at optimal design solution.
IV. Runner and Gate Connection Method
Connection between runner and gate should be machined into a bevel and transitioned with a rounded edge to facilitate flow and filling of molten plastic, as shown in Figure 5-35.
Figure 5-35 Connection method between runner and gate
V. Runner Balance
Flow balance is a very important issue in injection molding. If molten plastic flows unevenly within mold cavity, it can lead to a series of problems such as overpressure, warpage, and excessive clamping force. Flow balance is typically a concern in injection molds with symmetrically arranged cavities. However, in practical applications, to save production costs, different sized plastic parts are often designed into same mold. Therefore, asymmetric multi-cavity injection molds must also consider flow balance, ensuring that distal portions of products of different sizes are filled with melt at same pressure at the same time. Flow balance is essential for product quality.
One of main purposes of runner system in a multi-cavity mold is to deliver a uniform and consistent flow of melt to each cavity. Geometrically balanced runners (all runner branches are of equal length and have symmetrical cross-sectional shapes) have long been considered to provide the most suitable "natural balance." In reality, absolute runner balance is impossible; designing runners in a geometrically symmetrical form usually only achieves relative balance. Figure 5-36 shows a multi-cavity mold for molding a single product. Although runner branches are geometrically symmetrical, there are always some variations between cavities near mold center (shaded areas) and cavities farther from center. In most cases, imbalance becomes more pronounced when number of cavities exceeds four. However, this imbalance actually depends on number of branches in runner system. Molds with fewer cavities (such as single-cavity molds) can also experience imbalance problems, primarily depending on distribution of runner system.
One of main purposes of runner system in a multi-cavity mold is to deliver a uniform and consistent flow of melt to each cavity. Geometrically balanced runners (all runner branches are of equal length and have symmetrical cross-sectional shapes) have long been considered to provide the most suitable "natural balance." In reality, absolute runner balance is impossible; designing runners in a geometrically symmetrical form usually only achieves relative balance. Figure 5-36 shows a multi-cavity mold for molding a single product. Although runner branches are geometrically symmetrical, there are always some variations between cavities near mold center (shaded areas) and cavities farther from center. In most cases, imbalance becomes more pronounced when number of cavities exceeds four. However, this imbalance actually depends on number of branches in runner system. Molds with fewer cavities (such as single-cavity molds) can also experience imbalance problems, primarily depending on distribution of runner system.
Figure 5-36 Runner layout (material in shaded area will be subjected to high shear forces).
In commonly used H-shaped runner arrangements, such as 8-cavity mold shown in Figure 5-36(a) (only half is shown), parts molded in cavities closer to interior (closer to main runner) are typically larger and heavier. It is expected that mechanical properties of parts molded in different areas of mold will also be inconsistent. This is particularly pronounced when using fiber-reinforced materials, where fiber length variation reaches 2:1, and direct result of change in runner shear stress is a significant alteration in impact strength. Furthermore, to ensure sufficient pressure retention in outer cavities, middle cavities often overflow due to excessive molten material. For many years, this mold imbalance has been misdiagnosed as being caused by changes in mold temperature, cavity dimensions, and gravity (or mold plate deformation) due to mold orientation.
Flow of plastic in a runner is quite complex due to variations in shear rate, temperature, and material viscosity along runner length and cross-section. At all flow rates, shear rate is highest near outermost region of runner, and zero in the middle region (see Figure 5-37). It is expected that shear rate is highest at runner and gate within mold, and similarly, melt velocity is also highest there.
High shear rate region near outer wall has multiple effects on viscosity. Viscosity decreases in this region because of: non-Newtonian properties of material; and frictional heat caused by these non-Newtonian properties. This frictional heat makes temperature of melt in outer layer of runner higher than in inner layer. Although some heat can be dissipated to cooler mold wall through conduction, high temperature of outer layer will persist. In hot runners, especially in injection or transfer molding of thermosetting materials, frictional heat of outer layer will be superimposed on heat gained from heating outer mold wall.
In runner systems with more than two branch runners, uneven shear distribution across runner cross-section will cause flow and material imbalance. Imbalance between cavities is well-established. As polymer melt flows downwards along main runner, a high shear zone forms around outer perimeter of runner, as shown in section C-C of Figure 5-37. For simplicity, frozen layer formed on runner wall is not shown; diagram only illustrates material flow. When flow branches along branch runners, high-shear (hotter) outer layer on one side of main runner (area A in Figure 5-37) will flow along left side of second left branch runner. Low-shear (cooler) central laminar flow of main runner (area B in Figure 5-37) will flow to opposite side of that runner. Situation is similar in second right branch runner. As a result, characteristics of flow on one side of second branch runner differ from those on the other side (section D-D). If melt that has passed through second branch runner then enters third branch runner, an imbalance occurs between cavities filled by these runners.
In commonly used H-shaped runner arrangements, such as 8-cavity mold shown in Figure 5-36(a) (only half is shown), parts molded in cavities closer to interior (closer to main runner) are typically larger and heavier. It is expected that mechanical properties of parts molded in different areas of mold will also be inconsistent. This is particularly pronounced when using fiber-reinforced materials, where fiber length variation reaches 2:1, and direct result of change in runner shear stress is a significant alteration in impact strength. Furthermore, to ensure sufficient pressure retention in outer cavities, middle cavities often overflow due to excessive molten material. For many years, this mold imbalance has been misdiagnosed as being caused by changes in mold temperature, cavity dimensions, and gravity (or mold plate deformation) due to mold orientation.
Flow of plastic in a runner is quite complex due to variations in shear rate, temperature, and material viscosity along runner length and cross-section. At all flow rates, shear rate is highest near outermost region of runner, and zero in the middle region (see Figure 5-37). It is expected that shear rate is highest at runner and gate within mold, and similarly, melt velocity is also highest there.
High shear rate region near outer wall has multiple effects on viscosity. Viscosity decreases in this region because of: non-Newtonian properties of material; and frictional heat caused by these non-Newtonian properties. This frictional heat makes temperature of melt in outer layer of runner higher than in inner layer. Although some heat can be dissipated to cooler mold wall through conduction, high temperature of outer layer will persist. In hot runners, especially in injection or transfer molding of thermosetting materials, frictional heat of outer layer will be superimposed on heat gained from heating outer mold wall.
In runner systems with more than two branch runners, uneven shear distribution across runner cross-section will cause flow and material imbalance. Imbalance between cavities is well-established. As polymer melt flows downwards along main runner, a high shear zone forms around outer perimeter of runner, as shown in section C-C of Figure 5-37. For simplicity, frozen layer formed on runner wall is not shown; diagram only illustrates material flow. When flow branches along branch runners, high-shear (hotter) outer layer on one side of main runner (area A in Figure 5-37) will flow along left side of second left branch runner. Low-shear (cooler) central laminar flow of main runner (area B in Figure 5-37) will flow to opposite side of that runner. Situation is similar in second right branch runner. As a result, characteristics of flow on one side of second branch runner differ from those on the other side (section D-D). If melt that has passed through second branch runner then enters third branch runner, an imbalance occurs between cavities filled by these runners.
Figure 5-37 Cross-sectional view of high and low shear zones
Based on above analysis, the fewer cavities a precision plastic part has, the better; generally, it should not exceed four cavities.
1. Cavity Configuration
Single-cavity molds do not present a cavity configuration issue. Multi-cavity molds require consideration of cavity arrangement, including determining number of cavities and their arrangement. There are many methods for determining number of cavities, such as considering production volume, cost, empirical curves (relationship between number of cavities and production volume of plastic parts), selection of injection molding machine type, and rated parameters (injection volume, clamping force, injection pressure, etc.). First, determine number of cavities based on production volume of plastic parts. Then, verify number of cavities using rated parameters of injection molding machine and compare them to obtain economical number of cavities. Generally, number of cavities is mainly determined based on production volume and quality requirements of plastic parts.
Cavity arrangement affects design of mold structure, gate, and runner. There are many types of cavity arrangements. Based on shape of runner layout, they can be divided into O-shaped arrangement (also called circumferential arrangement or spoke arrangement), I-shaped arrangement (also called linear arrangement), H-shaped arrangement, X-shaped arrangement, Y-shaped arrangement, and mixed arrangements, among others. Arrangement of cavities is determined by factors such as whether plastic part is precision molded, whether mold structure involves core pulling, type of plastic part, runner length, processing difficulty, number of cavities, and flow balance. In multi-cavity molds, runner arrangements are divided into balanced and unbalanced types, with a balanced arrangement being preferred. A balanced arrangement means that length, cross-sectional shape, and size of runners from the end of main runner to each individual cavity are all equal. This design allows plastic to fill each cavity evenly.
Advantage of an unbalanced arrangement is that it can shorten the total runner length when there are many cavities. When runner length is long, it can be extended to serve as a cold slug well, preventing cold material from entering cavities.
I-shaped and H-shaped runner arrangements offer good balance, but in multi-cavity molds, due to numerous bends and longer flow paths, heat and pressure losses are significant. Therefore, they are more suitable for plastics with good flowability, such as PE, PP, and PA. An H-shaped arrangement is shown in Figure 5-38. X-shaped arrangement of runners has advantage of fewer turns, reducing energy loss. However, its disadvantage is that in multi-cavity molds, it doesn't utilize mold's effective area as well as H-shaped arrangement. X-shaped arrangement is shown in Figure 5-39(a). In practice, multi-cavity molds often use complex arrangements of multiple H-shaped and X-shaped runners; these arrangements are balanced runner layouts, as shown in Figures 5-39(b) and (c).
Based on above analysis, the fewer cavities a precision plastic part has, the better; generally, it should not exceed four cavities.
1. Cavity Configuration
Single-cavity molds do not present a cavity configuration issue. Multi-cavity molds require consideration of cavity arrangement, including determining number of cavities and their arrangement. There are many methods for determining number of cavities, such as considering production volume, cost, empirical curves (relationship between number of cavities and production volume of plastic parts), selection of injection molding machine type, and rated parameters (injection volume, clamping force, injection pressure, etc.). First, determine number of cavities based on production volume of plastic parts. Then, verify number of cavities using rated parameters of injection molding machine and compare them to obtain economical number of cavities. Generally, number of cavities is mainly determined based on production volume and quality requirements of plastic parts.
Cavity arrangement affects design of mold structure, gate, and runner. There are many types of cavity arrangements. Based on shape of runner layout, they can be divided into O-shaped arrangement (also called circumferential arrangement or spoke arrangement), I-shaped arrangement (also called linear arrangement), H-shaped arrangement, X-shaped arrangement, Y-shaped arrangement, and mixed arrangements, among others. Arrangement of cavities is determined by factors such as whether plastic part is precision molded, whether mold structure involves core pulling, type of plastic part, runner length, processing difficulty, number of cavities, and flow balance. In multi-cavity molds, runner arrangements are divided into balanced and unbalanced types, with a balanced arrangement being preferred. A balanced arrangement means that length, cross-sectional shape, and size of runners from the end of main runner to each individual cavity are all equal. This design allows plastic to fill each cavity evenly.
Advantage of an unbalanced arrangement is that it can shorten the total runner length when there are many cavities. When runner length is long, it can be extended to serve as a cold slug well, preventing cold material from entering cavities.
I-shaped and H-shaped runner arrangements offer good balance, but in multi-cavity molds, due to numerous bends and longer flow paths, heat and pressure losses are significant. Therefore, they are more suitable for plastics with good flowability, such as PE, PP, and PA. An H-shaped arrangement is shown in Figure 5-38. X-shaped arrangement of runners has advantage of fewer turns, reducing energy loss. However, its disadvantage is that in multi-cavity molds, it doesn't utilize mold's effective area as well as H-shaped arrangement. X-shaped arrangement is shown in Figure 5-39(a). In practice, multi-cavity molds often use complex arrangements of multiple H-shaped and X-shaped runners; these arrangements are balanced runner layouts, as shown in Figures 5-39(b) and (c).
Common O-shaped runner arrangements are shown in Figure 5-40. For some simple, long, narrow products, such as long ladles, O-shaped arrangement can achieve more cavity positions on mold, thus reducing injection molding costs. However, for molds with complex shapes, if cavities cannot be completely machined into finished product using CNC and require EDM, mold manufacturing cost will increase significantly. Because different locations require different electrodes, electrodes cannot be used in multiple cavities. Additional mold cost includes electrode material costs, electrode processing costs, EDM (electrical discharge machining) costs.
Figure 5-40 Common O-shaped flow channel arrangements
Unbalanced arrangement, see Figure 5-41. This arrangement results in shorter runners, facilitating cavity layout, and is frequently used in small plastic parts or parts with moderate precision to reduce costs.
Unbalanced arrangement, see Figure 5-41. This arrangement results in shorter runners, facilitating cavity layout, and is frequently used in small plastic parts or parts with moderate precision to reduce costs.
Figure 5-41 Unbalanced layout
2. Generalized Runner Balancing
In a single-cavity mold, melt front reaches all ends of cavity simultaneously, which is called flow balancing. For multi-cavity molds, melt front reaches ends of all cavities at the same time, which is also called flow balancing. Flow balancing design results in a more uniform distribution of melt pressure, temperature, and volume shrinkage, leading to better part quality.
Runner systems are generally divided into naturally balanced runner systems and unbalanced runner systems. In a naturally balanced runner system, all flow paths have same shape, size, and length, therefore melt flow characteristics in each runner path are also same. In non-naturally balanced runner systems, geometry and length of each runner path differ, resulting in varying flow resistance of melt in each path.
During injection filling stage, melt flow imbalance is a significant cause of warpage in molded parts. Ideal filling pattern involves melt maintaining a constant frontal velocity throughout filling process, reaching all parts of cavity simultaneously. There are many methods to describe whether filling process is balanced. With identical injection parameters and cavity structure, gate design that minimizes energy consumption during molding often achieves balanced melt filling. Minimizing energy consumption is equivalent to minimizing injection pressure required to complete filling process. Broadly speaking, runner balance can be understood in following three ways:
① Principle of flow balance: Runner design within mold should ensure that all runners simultaneously have an equal pressure drop during filling.
② Principle of a constant pressure gradient: Ideal filling method is a pressure gradient method, meaning that pressure drop per unit length remains constant throughout the entire runner domain.
③ In addition to traditional runner and gate balance, the cooling system must also be balanced.
In a broader sense, concept of gating system balance extends beyond traditional balance of runners and gates to include balancing of cooling system. Balanced cooling has two aspects: first, for multi-cavity molds, cooling water channels surrounding each cavity must have same position and length; second, for large single-cavity molds, each part of product must have same or equivalent cooling circuit. This type of balanced cooling system is particularly important for large, precision injection molded products.
2. Generalized Runner Balancing
In a single-cavity mold, melt front reaches all ends of cavity simultaneously, which is called flow balancing. For multi-cavity molds, melt front reaches ends of all cavities at the same time, which is also called flow balancing. Flow balancing design results in a more uniform distribution of melt pressure, temperature, and volume shrinkage, leading to better part quality.
Runner systems are generally divided into naturally balanced runner systems and unbalanced runner systems. In a naturally balanced runner system, all flow paths have same shape, size, and length, therefore melt flow characteristics in each runner path are also same. In non-naturally balanced runner systems, geometry and length of each runner path differ, resulting in varying flow resistance of melt in each path.
During injection filling stage, melt flow imbalance is a significant cause of warpage in molded parts. Ideal filling pattern involves melt maintaining a constant frontal velocity throughout filling process, reaching all parts of cavity simultaneously. There are many methods to describe whether filling process is balanced. With identical injection parameters and cavity structure, gate design that minimizes energy consumption during molding often achieves balanced melt filling. Minimizing energy consumption is equivalent to minimizing injection pressure required to complete filling process. Broadly speaking, runner balance can be understood in following three ways:
① Principle of flow balance: Runner design within mold should ensure that all runners simultaneously have an equal pressure drop during filling.
② Principle of a constant pressure gradient: Ideal filling method is a pressure gradient method, meaning that pressure drop per unit length remains constant throughout the entire runner domain.
③ In addition to traditional runner and gate balance, the cooling system must also be balanced.
In a broader sense, concept of gating system balance extends beyond traditional balance of runners and gates to include balancing of cooling system. Balanced cooling has two aspects: first, for multi-cavity molds, cooling water channels surrounding each cavity must have same position and length; second, for large single-cavity molds, each part of product must have same or equivalent cooling circuit. This type of balanced cooling system is particularly important for large, precision injection molded products.











